Yamaha CLP-F01 Sub-mode Dual Balance, Dual Detune, Voice 1 Octave Shift Voice 2 Octave Shift

Page 44

ENGLISH

F3. Dual Mode Functions

You can set various parameters for Dual mode to optimize the settings for the songs you play, such as adjusting the volume balance between two voices.

Dual mode function settings are set individu- ally for each voice combination.

1.Select the voices in Dual mode and engage

Function mode and select .

2.Press the [+/YES] button to engage the Dual mode function’s sub-mode, then use the [TEMPO/FUNCTION# ▼ ▲] buttons to select the desired sub-mode. Press the [–/NO] [+/ YES] button to assign values.

NOTE

If Dual mode is not engaged, will appear instead of and you will be unable to select Dual mode functions.

You can switch from Function mode to Dual mode.

Sub-mode

Dual Balance

Setting range: 0 – 20 (A setting of “10” produces an equal balance between the two Dual mode voices. Settings below “10” increase the volume of Voice 2 in relation to Voice 1, and settings above “10” increase the volume of Voice 1 in relation to Voice 2.)

Normal setting: Different for each voice combina- tion.

You can set one voice as the main voice, and another voice as a softer, mixed voice.

Dual Detune

Setting range: -10 – 0 – 10 (With positive values, the pitch of Voice 1 is raised and the pitch of Voice 2 is lowered. With neg- ative values, the pitch of Voice 1 is lowered and the pitch of Voice 2 is raised.)

TIP

The available setting range is wider in the lower range (± 60 cents for A-1), and narrower in the higher range (± 5 cents for C7). (100 cents equal one semitone.)

Normal setting: Different for each voice combina- tion.

Detune Voice 1 and Voice 2 for Dual mode to create a thicker sound.

Voice 1 Octave Shift

Voice 2 Octave Shift

Setting range: –1, 0, 1

Normal setting: Different for each voice combina- tion.

You can shift the pitch up and down in octave steps for Voice 1 and Voice 2 independently. Depending on which voices you combine in Dual mode, the combination may sound better if one of the voices is shifted up or down an octave.

Voice 1 Effect Depth

Voice 2 Effect Depth

Setting range: 0 – 20

Normal setting: Different for each voice combina- tion.

These functions make it possible to individually set the depth of the effect for Voices 1 and 2 for Dual mode. (The effect depth settings cannot be changed unless the [EFFECT] is ON. Function mode must be exited before the [EFFECT] can be turned ON.)

• “Voice 1” and “Voice 2” are explained on page 28.

Reset

This function resets all Dual mode functions to their default values. Press the [+/YES] button to reset the val- ues.

TIP

SHORTCUT:

You can jump directly to the Dual mode functions by pressing the [TEMPO/FUNCTION#] button while holding the two Dual mode voice buttons.

To exit Function mode, you still need to press the [TEMPO/ FUNCTION#] button so that the TEMPO indicator lights up.

44CLP-F01Detailed Settings – [FUNCTION]

Page 43 Page 45
Image 44
Page 43 Page 45
Contents CLP-F01 Special Message Section Precautions Connections Trademarks IntroductionReference AppendixTable of Contents Application Index Accessories TuningBench may be included or optional, depending on your locale TransportingFeatures TransposeBefore Using the Clavinova Key CoverTo open the key cover To close the key coverTo replace the music rest Music RestTo position the music rest for use Turning the Power On Connect the power cordTurn the power on Power indicatorUsing the Speaker Switch Setting the VolumeUsing Headphones option Memo Clavinova’s various functions Panel Controls and TerminalsTop panel ConnectorsPanel Controls and Terminals Display Listening to the Demonstration Tunes Listening to 50 Piano Preset Songs Engage Preset Song modePlay any of the 50 preset songs Stop playbackExit from Preset Song mode How to use the practice functionsTurn off the playback part you wish to practice Start playback and playingLeft Pedal Start/Stop Repeat for 50 Preset Songs Will appear on the disUsing the Pedals Selecting & Playing VoicesSelecting Voices Damper Right PedalSoft Left Pedal Normal settingSostenuto Center Pedal Adjusting Reverb Depth Adjusting Effect DepthDepth 0 no effect Depth 0 no effect Depth 20 maximum effect depthChanging the volume when Fixed is selected Touch Sensitivity TouchTransposition Transpose TransposeExit Dual mode and return to normal play mode Combining Two Voices Dual modeEngage Dual mode Engage Split mode SplitExit Split mode and return to normal play mode Press the Split button again so that its indicator goes outSelect a voice for the right hand Select a voice for the left handUsing the Metronome Adjusting the tempoAdjusting the time signature Start the metronomeMake all the initial settings Recording Your PerformanceSelect a song for recording Recording vs. SavingEngage Record mode Select the record trackStart recording Stop recordingRe-recording Track Recording to TrackEntire Song Individual TracksVoice selection Press the REC button to exit Record mode You can change the following initial settingsChange the settings via the panel controls Midi connectors Playing Back Recorded SongsPlaying Back a Song Select the desired songUseful Playback Functions Turning track playback on and offAssigning the START/STOP function to the left pedal SynchroDetailed Settings Function Parameter ListBasic Procedure in Function Mode Engage Function modeSelect a function Use the -/NO +/YES buttonsOperation Example 2 F3.1 Dual Balance Do the following when you finish using the func- tionOperation Example 1 F1. Fine tuning of the pitch Setting range About Each FunctionDisplay Value Hz HertzEqual PureMajor/PureMinorPythagorean MeanToneReset Sub-mode Dual BalanceDual Detune Voice 1 Octave Shift Voice 2 Octave ShiftSub-mode Split Point Split BalanceRight Voice Octave Shift Left Voice Octave Shift Right Voice Effect Depth Left Voice Effect DepthSub-mode Left Pedal Mode Keyoff Sample VolumeSoft Pedal Effect Depth Sustain Sample DepthF6. Metronome Volume Sub-mode Midi Transmit Channel SelectionSetting range ON/OFF Normal setting on Midi Receive Channel SelectionLocal Control ON/OFF Program Change ON/OFFProcedure Midi Transmit TransposePanel/Status Transmit Bulk Data DumpSub-mode Voice Midi Tuning Others Factory Preset RecallSetting range ON/OFF Normal setting OFF all groups Description of sub-modes VoiceMidi connectors To Host connectorAbout Midi Midi cablesConnectors ConnectionsAUX in R, L/L+R jacks AUX in L/L+R jack or AUX OUT L/L+R jackConnecting a Personal Computer On the power to the computer first, then to the ClavinovaType of serial cables and connection pin assignments ConnectionConnection Clavinova Host Select switch settingSet the Clavinova Host Select switch to Midi Computer Troubleshooting Problem Possible Cause and SolutionInsert the rear panel center Keyboard Stand AssemblyRemoving the panels Install the rear panels left and right Voltage SelectorFasten the rear panels securely Attach the fall-prevention bracketAfter completing the assembly, please check the following Review the assembly procedure and correct any errorsMove the Clavinova to an appropriate location Check the connectionPreset Voice List Voice Name Stereo Touch Dynamic Key-Off Voice DescriptionsWood Bass Demo Song List Piano Voice Demo DescriptionVoice Name Title Composer Voice Name Piano Voice DemoIndex Practicing a One-Hand Part Using 50 Preset Songs......20 Soft Pedal 16, 2416, 29 Start/Stop playbackAppendix Function Backup GroupFunction number Default Backup Group CLP-F01Appendix Panel Data Transmit Panel Data ContentsMidi Master Volume General Midi Mode On Data format F0H 7EH XnH 09H 01H F7HMidi Parameter Change table Multi Part Effect Midi MapMidi Parameter Change table Effect Midi Implementation Chart ON/OFF Memo Memo Please Keep this Manual FCC Information U.S.A North America Clavinova Web site English only Yamaha Manual Library
Top Page Image Contents