Yamaha CLP-F01 owner manual Connecting a Personal Computer

Page 54

ENGLISH

Connecting a Personal Computer

You can enjoy computer music data on the Clavinova by connecting a computer to the TO HOST (or MIDI) jack.

NOTE When the Clavinova is used as a tone module, performance data with voices that are not found on the Clavinova will not be played correctly.

“The Clavinova-Computer Connection,” is a supplementary guidebook that describes, for beginners, what you can do with your Clavinova and a personal computer and how to set up a Clavinova-Computer system (the manual is not written for any specific models). The document is available as a PDF file (in English) at the following Internet address.

Yamaha Manual Library:

http://www2.yamaha.co.jp/manual/english/

There are three methods by which to connect the Clavinova to a personal computer:

1.Connect the serial port on the computer to the Clavinova’s TO HOST jack (page 55).

2.Use a MIDI interface and the Clavinova’s MIDI connectors (page 56).

3.Use the USB port on the computer and the UX16, UX96, or UX256, a USB interface (page 57).

For more information, refer to the specified pages.

NOTE

When connecting the Clavinova to a personal computer, first turn off the power to both the Clavinova and the computer

 

before you connect any cables or set the HOST SELECT switch. After making the connections and switch settings, turn

 

on the power to the computer first, then to the Clavinova.

 

If you do not use the [TO HOST] jack of the Clavinova, make sure you disconnect the cable from the jack. If the cable is

NOTE

 

left connected, the Clavinova may not function properly.

 

 

 

 

NOTE

 

 

will appear in the display if the host computer is not turned on, the connecting cable is not properly connected,

 

 

 

 

the HOST SELECT switch is not in the proper position, or the MIDI driver or MIDI application is not active. In this situa-

 

tion, turn the power off to both the Clavinova and the computer, and check the cable connection and the position of the

 

HOST SELECT switch. Once the connection and HOST SELECT switch position is verified, turn the power of the com-

 

puter on first, then the Clavinova, and check whether the MIDI driver and MIDI application function properly.

 

When the [HOST SELECT] switch is set to “PC-1,” PC-2,” or “Mac,” you can use the [TO HOST] jack, but the MIDI con-

NOTE

 

nectors are disabled since no data transfer occurs via the MIDI connectors. On the other hand, when the [HOST

 

SELECT] switch is set to “MIDI,” you can use the MIDI connectors, but not the [TO HOST] jack since no data is trans-

 

ferred via the [TO HOST] jack.

54 CLP-F01Connections

Page 53 Page 55
Image 54
Page 53 Page 55
Contents CLP-F01 Special Message Section Precautions Connections Reference TrademarksIntroduction AppendixTable of Contents Application Index Bench may be included or optional, depending on your locale AccessoriesTuning TransportingFeatures TransposeTo open the key cover Before Using the ClavinovaKey Cover To close the key coverMusic Rest To position the music rest for useTo replace the music rest Turn the power on Turning the Power OnConnect the power cord Power indicatorSetting the Volume Using Headphones optionUsing the Speaker Switch Memo Clavinova’s various functions Panel Controls and TerminalsConnectors Panel Controls and TerminalsTop panel Display Listening to the Demonstration Tunes Play any of the 50 preset songs Listening to 50 Piano Preset SongsEngage Preset Song mode Stop playbackTurn off the playback part you wish to practice Exit from Preset Song modeHow to use the practice functions Start playback and playingLeft Pedal Start/Stop Repeat for 50 Preset Songs Will appear on the disSelecting Voices Using the PedalsSelecting & Playing Voices Damper Right PedalNormal setting Sostenuto Center PedalSoft Left Pedal Depth 0 no effect Adjusting Reverb DepthAdjusting Effect Depth Depth 0 no effect Depth 20 maximum effect depthChanging the volume when Fixed is selected Touch Sensitivity TouchTransposition Transpose TransposeCombining Two Voices Dual mode Engage Dual modeExit Dual mode and return to normal play mode Engage Split mode SplitSelect a voice for the right hand Exit Split mode and return to normal play modePress the Split button again so that its indicator goes out Select a voice for the left handAdjusting the time signature Using the MetronomeAdjusting the tempo Start the metronomeSelect a song for recording Make all the initial settingsRecording Your Performance Recording vs. SavingStart recording Engage Record modeSelect the record track Stop recordingRe-recording Track Recording to TrackIndividual Tracks Voice selectionEntire Song You can change the following initial settings Change the settings via the panel controlsPress the REC button to exit Record mode Playing Back a Song Midi connectorsPlaying Back Recorded Songs Select the desired songAssigning the START/STOP function to the left pedal Useful Playback FunctionsTurning track playback on and off SynchroDetailed Settings Function Parameter ListSelect a function Basic Procedure in Function ModeEngage Function mode Use the -/NO +/YES buttonsDo the following when you finish using the func- tion Operation Example 1 F1. Fine tuning of the pitchOperation Example 2 F3.1 Dual Balance Display Value Setting rangeAbout Each Function Hz HertzPythagorean EqualPureMajor/PureMinor MeanToneDual Detune ResetSub-mode Dual Balance Voice 1 Octave Shift Voice 2 Octave ShiftRight Voice Octave Shift Left Voice Octave Shift Sub-mode Split PointSplit Balance Right Voice Effect Depth Left Voice Effect DepthSoft Pedal Effect Depth Sub-mode Left Pedal ModeKeyoff Sample Volume Sustain Sample DepthF6. Metronome Volume Sub-mode Midi Transmit Channel SelectionLocal Control ON/OFF Setting range ON/OFF Normal setting onMidi Receive Channel Selection Program Change ON/OFFPanel/Status Transmit ProcedureMidi Transmit Transpose Bulk Data DumpSetting range ON/OFF Normal setting OFF all groups Sub-mode Voice Midi Tuning OthersFactory Preset Recall Description of sub-modes VoiceAbout Midi Midi connectorsTo Host connector Midi cablesConnectors ConnectionsAUX in R, L/L+R jacks AUX in L/L+R jack or AUX OUT L/L+R jackConnecting a Personal Computer On the power to the computer first, then to the ClavinovaType of serial cables and connection pin assignments ConnectionClavinova Host Select switch setting Set the Clavinova Host Select switch to MidiConnection Computer Troubleshooting Problem Possible Cause and SolutionKeyboard Stand Assembly Removing the panelsInsert the rear panel center Fasten the rear panels securely Install the rear panels left and rightVoltage Selector Attach the fall-prevention bracketMove the Clavinova to an appropriate location After completing the assembly, please check the followingReview the assembly procedure and correct any errors Check the connectionPreset Voice List Voice Name Stereo Touch Dynamic Key-Off Voice DescriptionsWood Bass Voice Name Title Composer Demo Song ListPiano Voice Demo Description Voice Name Piano Voice DemoIndex 16, 29 Practicing a One-Hand Part Using 50 Preset Songs......20Soft Pedal 16, 24 Start/Stop playbackAppendix Backup Group Function number Default Backup GroupFunction CLP-F01Appendix Panel Data Contents Midi Master VolumePanel Data Transmit General Midi Mode On Data format F0H 7EH XnH 09H 01H F7HEffect Midi Map Midi Parameter Change table EffectMidi Parameter Change table Multi Part Midi Implementation Chart ON/OFF Memo Memo Please Keep this Manual FCC Information U.S.A North America Clavinova Web site English only Yamaha Manual Library
Top Page Image Contents