Heat & Glo LifeStyle 8000TRD manual Table of Contents

Page 3

TABLE OF CONTENTS
Safety and Warning Information		2
Service Parts Lists		4
Section 1: Approvals and Codes		6
Appliance Certification		6
Installation Codes		6
u High Altitude Installations		6
Section 2: Getting Started		7
Introducing the Heat-N-Glo Gas Fireplaces		7
Pre-installation Preparation		7
Section 3: Installing the Fireplace		9
Constructing the Fireplace Chase		9
Step 1	Locating the Fireplace	9
u Step 2	Framing the Fireplace	10
Step 3	Installing the Vent System	12
	A. Vent System Approvals	12
	B. Installing Vent Components	20
	C. Vent Termination	23
Step 4	Positioning, Leveling, and
	Securing the Fireplace	26
u Step 5	The Gas Control Systems	26
Step 6	The Gas Supply Line	27
Step 7	Gas Pressure Requirements	27
Step 8	Wiring the Fireplace	28
Step 9	Finishing	30
Step 10 Installing Trim, Logs, and Ember Material		31
	Installing the Trim	31
	Positioning the Logs	31
	Shutter Settings	31
	Placing the Ember Material	31
	Glass Specifications	32
u Step 11	Before Lighting the Fireplace	32
Step 12	Lighting the Fireplace	32
After the Installation		32
u Section 4: Maintaining and Servicing Your Fireplace		33

u= Contains updated information.

3

Image 3

Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents 8000TRD 18 9 Log Set AssemblyIPI Ignition Allumage IPI Service Parts List / Liste des pièces de rechange 8000TRDCommon Parts / Piéces Communes Standing Pilot Ignition / D’ALLUMAGE PAR VeilleuseCertification Installation CodesHigh Altitude Installations Appliance CertificationPre-install Preparation Introducing the Heat-N-Glo Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 8000TRD Space Requirements Constructing the Fireplace ChaseLocating the Fireplace Clearance RequirementsFraming the Fireplace Framing Dimensions187mm 149mm 220mm DV-90D 164mm 216mm Terminations Kits Installing the Vent SystemVent System Approvals Identifying Vent ComponentsBreak Here Flue Restrictor InstructionsVertical Venting MAX .4 MChart Venting with One 90 Elbow Venting with ONE 1 90 ElbowVenting with TWO Elbows MIN MAX mm 610mm MAX .22m 914mm MAX .86m MAX .4m Venting with three 90 elbows Venting with Three 3 90 Elbows+ H 1 FT Installing Vent Components Stove Cement Must be Placed around5 Inch 127 MM Fireplace Starting COL To Install the Heat Shield Install Support BracketsContinue Adding Vent Components 12 Hole and Vent Pipe Vent Termination Positioned SO That the Arrow is Pointing UP4 184mm Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Standing Pilot Ignition System Vice Must be Wired Directly to the FIRE- Place Junction BOXPositioning, Leveling, and Securing the Fireplace Gas Control SystemsNatural Gas Propane Gas Supply LineGas Pressure Requirements Check for GAS LeaksPosition the wall switch in the desired position on a wall Wiring the FireplaceOptional Accessories Optional fan and remote control kits require thatBlack Optional Battery BACK-UP RED Brown Operation using Battery PowerSealant Material Hearth Extensions FinishingOutlet Grilles in ANY Manner Installing Trim, Logs, and Ember MaterialInstalling the Trim Shutter Settings Burner Placing the Ember MaterialBefore Lighting the Fireplace After the InstallationGlass Specifications 8000TRD 26 1/2 X 42 1/2 Tempered Double-check for faulty componentsReplacing old ember material Fireplace MaintenanceCleaning Glass Door Important Turn OFF the GAS Before Servicing Your Fireplace