Desa (V)CD36RPE, (V)CD36TNE, (V)CD36TPE, (V)CD36RNE Optional Wireless Remote Operation, Pilot

Page 35

Operating fireplace

Continued

6.Wait five (5) minutes to clear out any gas.

Then smell for.

gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety infor- mation above. If you don’t smell gas go to the next step.

7.Turn equipment shutoff valve counterclock- wise to the ON position. Do not force.

8.Close lower louver panel.

9.Turn on all electric power to the fireplace.

10.Turn the wall switch to the ON position.

11.Visually locate the pilot. The ignitor should begin to spark and

the main burner should ignite once flame appears at pilot.

•If lighting the appliance for the first time each season, it may take several attemps before the supply gas can reach the pilot and main burner.

•If the appliance will not stay lit after sev- eral attempts, follow the instructions To Turn Off Gas To Appliance, below, and call your service technician or gas supplier.

NOTICE: During initial operation of a new heater, the burning of residues from the manufacturing process of the firebox and logs willproduceapaper-burningsmell andorangeflames.Openawindow forthefirst fewhoursofoperation to adequately vent this smell.

Figure 64 - Pilot

TO TURN OFF GAS

TO APPLIANCE

1.Turn off the wall switch.

2.Turn off all electric power to the appliance if service is to be performed.

3.Open lower louver panel.

4.Turn equipment shutoff valve clockwise to OFF. Do not force.

5.Close lower louver panel.

Optional Wireless

Remote Operation

Note: The WRC receiver and hand-held remote control kit must be purchased separately (see Accessories, page 45). Follow installation in- structions included with the remote control.

1.Turn equipment shutoff valve to ON posi- tion. You can now turn the burner on and off with the hand-held remote unit.

IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation.

2.Press the ON/OFF button to turn the burner on and off.

IMPORTANT: Do not leave the selectorswitch inthe REMOTE or ON position when the pilot is not lit. This will drain the battery.

operating optional

GWMT1 - Wall Mounted

Thermostat

WARNING: Do not con- nect the thermostat to a power source. Electrical shock and/or a fire hazard will occur.

Light the fireplace as instructed in Lighting Instructions on page 34. Set wall thermostat to desired temperature.

This thermostat has been electronically cali- brated at the factory and requires no adjust- ment or leveling.

Upon installation, the thermostat must be al- lowed to stabilize at room temperature for a minimum of 30 minutes for proper operation. To turn the fireplace off, adjust thermostat to the lowest setting and turn the gas control knob back to PILOT. The pilot will remain lit.

IMPORTANT: To turn the pilot off, turn the gas control knob on the heater to the OFF position.

operating optional blower accessory

Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the right side of the switch bracket to the left just inside the louver panel. The BK manual blower and the BKT thermo- statically-controlled blower have an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

116035-01E

www.desatech.com

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents VCD36TN, VCD36TNE Natural GAS ModelsVCD36RN, VCD36RNE PROPANE/LP GAS ModelS PROPANE/LP GAS ModelsTable of Contents Safety Information High traffic areas Product IdentificationLocation and space requirements Product FeaturesPre-Installation Preparation Local CodesClearances Packaging and RemovalMantel Clearances Framing and finishingSide Clearances for Combustible Materials Termination CAP AIR Supply Inlet GAS Meter Location of Termination CapInstallation Precautions Venting Installation InstructionsTwisting, bending, etc Installation PlanningLocation of the fireplace Feet. Use wall straps for this purposeInstalling Siding Standoff Combustible Exterior Wall Wall Firestop Installing Inner Wall FirestopHorizontal Termination Venting InstallationSnorkel 45 and 30 Offset with Wall Strap Installation for vertical terminationTwist-lock the vent cap onto the last section of vent pipe Flat Ceiling InstallationConnect a section of pipe and extend up through the hole Vertical Venting Vertical Termination Configurations for Rear VentHigh Wind Termination Vertical Termination Configurations for Top VentDesa 5/8 Pipe & Vent Kits Number Description Parts list for venting kits and componentsElectrical Supply Connection Fireplace InstallationInstalling optional blower accessories Model BK InstallationBlower Model BK Plug in blower power cordPlug in blower power cord to duplex outlet Model BKT InstallationWiring Diagrams Locate the two plastic mounting clips provided with the kit Installing Remote ReceiverAttach the terminal wires to the battery. see Figure Installing and Activating the Remote ReceiverInstallation Items Needed High Altitude installationInstalling Gas Piping to Fireplace Location Important Fireplaces when factory equipped for use at highPropane/LP Supply TankExternal Regulator Vent Pointing Down Connecting Fireplace to GAS SupplyClose equipment shutoff valve see Figure Pressure Testing Gas Supply Piping SystemChecking GAS Connections Test Pressures Equal To or Less Than Psig 3.5 kPaRemoving Top Louver Trim Panel Pressure Testing Fireplace Gas ConnectionsRemoving Lower Louver Access Panel Removing/Replacing Glass DoorRemoving Glass Door Installing LOGS, lava rock and glowing embersOpen the bag of ember materials Millivolt For your safety Read before lightingOperating Fireplace Lighting InstructionsRemote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional Hand-HeldThermostat Series Model HRC200 Operating optional GWMT1 Wall Mounted Thermostat Operating optional blower accessoryElectronic ingnition For your safety Read before lighting Pilot Optional Wireless Remote OperationBurner Flame Pattern Pilot assemblyIf you pilot assembly does not meet these require- ments Inspecting BurnersPilot and burners Cleaning MaintenanceGlass Door Venting system TroubleshootingObserved Problem Possible Cause Remedy LogsTurn on gas supply or open When ignitor button is pressedProblem could be caused by Burner orifice clogged Clean burner see Cleaning Is litOperation Processes and logs curing Hours of operation When burner is lit HI position when burner isOr shut off Service person Remote does not function Tery is power is lowStatement above Electronic Ignition Statement at top Gas leak. See WarningSpecifications Replacement PartsService Hints Technical ServiceThermostatically Controlled Blower KIT BKT AccessoriesPROPANE/NATURAL GAS Manual Blower KIT BKIllustrated Parts Breakdown Parts List Illustrated parts breakdown Washer, Flat 7/8 ID x 2 OD x 1/8 Thick Illustrated Parts Breakdown CD36TNEV Limited Warranty DIRECT-VENT Fireplace Warranty InformationKeep this Warranty

V)CD36RN, (V)CD36TN, (V)CD36RPE, (V)CD36RNE, (V)CD36RP specifications

The Desa (V)CD36TPE, (V)CD36TP, (V)CD36TNE, (V)CD36RP, and (V)CD36RNE represent a series of cutting-edge heating solutions designed to meet the diverse needs of modern users. These models stand out for their efficiency, user-friendly features, and advanced technologies that ensure optimal performance and comfort.

One of the main features of these Desa models is their impressive heating capacity. Each unit provides a reliable source of warmth, making them suitable for various environments, from residential homes to larger commercial spaces. The versatility of these models ensures that they can accommodate different room sizes and heating requirements effortlessly.

The Desa models incorporate advanced heating technologies, including efficient radiant heating systems. This technology allows for quicker heat distribution and a more comfortable ambient temperature. Users can enjoy the benefits of even heat coverage, eliminating cold spots and ensuring a pleasant living or working environment.

Energy efficiency is another critical characteristic of the Desa models. Designed with modern energy-saving features, these units help reduce energy consumption while maintaining powerful heating capabilities. This aspect not only leads to cost savings on energy bills but also contributes to a more sustainable approach to heating.

Convenience is paramount in the design of the (V)CD36 series. Many of these models come equipped with programmable thermostats and remote control options, enabling users to set their desired heating schedule with ease. This flexibility allows for personalized comfort and lets users maintain their preferred temperatures without unnecessary manual adjustments.

Safety features are also a top priority in the (V)CD36 series. Each model is equipped with essential safety mechanisms, including automatic shut-off systems and tip-over protection, ensuring peace of mind when the units are in operation.

The aesthetic design of the Desa (V)CD36 series complements various interior styles. With sleek finishes and a modern silhouette, these heating solutions blend seamlessly into any décor while providing essential functionality.

In summary, the Desa (V)CD36TPE, (V)CD36TP, (V)CD36TNE, (V)CD36RP, and (V)CD36RNE models exemplify innovation in heating technology, offering energy efficiency, safety, and user convenience. These features make them an excellent choice for anyone seeking reliable and effective heating solutions.
Top Page Image Contents