Desa CGCDV42PR Removing/Replacing Glass Door, Removing Louver Panels, Removing Glass Door

Page 25

Fireplace

Installation

Continued

Installing 9-Volt Alkaline Battery in Hand-

Held Remote Control Unit

1. Remove battery cover on back of remote control unit.

2. Attach terminal wires to a 9-volt alkaline battery (not included). Place battery into the battery housing.

Removing Louver Panels

Remove the top and bottom louver panels by si- multaneously pulling both top end spring latches towards the center of the appliance until they are disengaged from the locating holes (see Figure 41). Repeat for bottom spring latches and pull the lou- vers outward. To install or replace items removed, simply reverse the procedures above.

3. Replace battery cover onto remote control unit.

Battery Cover

Remote

Control Unit

 

Louver

Panel

Spring Latch

Terminal

 

Wires

 

9-Volt

Battery

Housing

Battery

 

Figure 40 - Installing Battery in Hand-

Held Remote Control Unit

Removing/Replacing Glass Door

CAUTION: Do not operate this fireplace with a broken glass door panel or without the glass door panel securely in place. For replacement part informa- tion see Replacement Parts, page 37.

CAUTION: Wear gloves and safety glasses while handling or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass.

WARNING: If fireplace has been running, turn off and un- plug fireplace. Let cool before re- moving glass door or louvers.

Figure 41 - Removing Louver Panel

Removing Glass Door

If replacement of glass is necessary, the entire assembly, glass and frame, must be replaced. If glass is broken, wear gloves and tape the remaining fragments onto the frame.

1.Remove screen assembly by pushing the rod either left or right and then down and forward to remove screen/rod assembly from the fire- box. Set assembly aside.

2.Lift up on latches to unlock. There are two on top of firebox and two below firebox that hold glass door in place (see Figure 42).

3.While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on the left side of door frame assembly (see Figure 42).

Unlock Lock

Latch

Screw

Hinge

Glass Frame

Assembly

Figure 42 - Removing/Replacing Glass

Door

116236-01G

www.desatech.com

25

Image 25
Contents Patent Pending What to do if YOU Smell GASSafety Information Table of ContentsSafety Information Local Codes Product IdentificationHigh traffic areas Pre-Installation Preparation Product FeaturesLocation and space requirements This fireplace does not require electricity to operateMinimum clearances to combustibles for Clearances42 1067 mm Front 36 914 mm Top of Standoffs VentNoncombustible mantels at any height above Framing and finishingFireplace Balcony with Perpendicular Side Wall Location of Termination CapInstallation Precautions Venting Installation InstructionsInstallation Planning Installing Horizontal Vent Cap Noncombustible Exterior Round Termination Ground Floor InstallationRecommended Applications Corner ground floor installation Corner InstallationHorizontal System Installation Using TWO 90 Elbows Flat Ceiling Installation Installation for vertical terminationConnect a section of pipe and extend up through the hole Twist-lock the vent cap onto the last section of vent pipe Vertical Venting High Altitude InstallationDesa 5/8 Pipe & Vent Kits Number Description Parts list for venting kits and componentsInstalling optional blower accessories Fireplace InstallationModel BK Installation Plug in blower power cordBlower Model BKT Model BKT InstallationBlower Wiring Diagram Installing Gas Piping to Fireplace LocationInstallation Items Needed Propane/LP From Connecting Fireplace to GAS SupplyTest Pressures Equal To or Less Than Psig 3.5 kPa Checking GAS ConnectionsInstalling Remote Receiver Pressure Testing Fireplace Gas ConnectionsRemoving/Replacing Glass Door Replace battery cover onto remote control unitRemoving Louver Panels Removing Glass DoorInstalling Brick liner Models BL42DASA and BL42DHASA Installing lava rock and glowing embersReplace screen/rod assembly by reversing step Cleaning Glass DoorOperating Fireplace For your safety Read before lightingLighting Instructions Close top and bottom louversOptional Hand-Held To Turn OFF GAS To Appliance Manual Lighting ProcedureRemote Operation Thermostat Series Model HRC200 On/Off Series Model HRC100Pilot assembly Operating optional blower accessoryKey Pad Lock Feature Inspecting BurnersBurner Flame Pattern Cleaning MaintenanceGlass Door Logs Pilot and burnersVenting system Observed Problem Possible Cause Remedy TroubleshootingBurner orifice clogged Clean burner see Cleaning Is lit Problem could be caused by Replace pilot assemblyAfter pilot lights, keep gas Long enough Control knob pressedTery power is low When burner is lit HI position when burner isTurning gas control knob to Cold Minute Air in gas line Operate burner until air isStatement above Gas leak. See WarningService Hints Replacement PartsTechnical Service SpecificationsIllustrated Parts Breakdown Parts List 19 18 116236-01G Burner Pan Assembly Accessories Wall mounted thermostat control kit gwmt1 Wall mounted on/off switchGwmS2 Not Shown Keep this Warranty Warranty InformationLimited Warranty DIRECT-VENT Fireplace