Desa CGCDV42NR Operating Fireplace, For your safety Read before lighting, Lighting Instructions

Page 27

Fireplace

Installation

Continued

6.Install rear brick panel first. Rest bottom edge of panel on back edge of burner assembly (see Figure 44).

7.Install left side brick panel by sliding it be- tween the burner assembly and the side of the firebox (see Figure 44).

8.Install the right brick panel using the same method described in step 6 for left brick panel.

9.Replace deflector shield using screws removed in step 4.

10.Using screws removed in step 4, replace plenum and attach to burner.

11.Using screws removed in step 3, replace log/grate assembly. Be careful when replac- ing log/grate assembly not to chip logs on burner.

12.Install lava rock and glowing embers. See

Installing Lava Rock and Glowing Embers, page 26.

13.Close glass door and lock latches on top and bottom of door and replace screen. See Remov- ing Glass Door, steps 5 and 6 on page 25.

14.Close top and bottom louvers.

Left Side

Brick Panel

Rear Brick Panel

Figure 44 - Installing Rear Brick Panel

Operating Fireplace

for your safety

Read before lighting

WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result causing property damage, per- sonal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

lighting

instructions

1.STOP! Read the safety information above.

2.Open lower louver panel.

3.Turn off all electric power to the fireplace.

4.Push in gas control knob slightly and turn

clockwise to OFF.

5.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor.

If you smell gas, STOP! Follow “B” in the safety information above. If you don't smell gas, go to the next step.

6.The pilot is located by the main burner and should not require accessing for lighting.

116236-01G

www.desatech.com

27

Image 27
Contents Patent Pending What to do if YOU Smell GASSafety Information Table of ContentsSafety Information Product Identification Local CodesHigh traffic areas This fireplace does not require electricity to operate Product FeaturesPre-Installation Preparation Location and space requirementsFront 36 914 mm Top of Standoffs Vent ClearancesMinimum clearances to combustibles for 42 1067 mmFraming and finishing Noncombustible mantels at any height aboveFireplace Balcony with Perpendicular Side Wall Location of Termination CapInstallation Precautions Venting Installation InstructionsInstallation Planning Installing Horizontal Vent Cap Noncombustible Exterior Round Termination Ground Floor InstallationRecommended Applications Corner ground floor installation Corner InstallationHorizontal System Installation Using TWO 90 Elbows Installation for vertical termination Flat Ceiling InstallationConnect a section of pipe and extend up through the hole Twist-lock the vent cap onto the last section of vent pipe Vertical Venting High Altitude InstallationDesa 5/8 Pipe & Vent Kits Number Description Parts list for venting kits and componentsPlug in blower power cord Fireplace InstallationInstalling optional blower accessories Model BK InstallationBlower Model BKT Model BKT InstallationInstalling Gas Piping to Fireplace Location Blower Wiring DiagramInstallation Items Needed Propane/LP From Connecting Fireplace to GAS SupplyTest Pressures Equal To or Less Than Psig 3.5 kPa Checking GAS ConnectionsInstalling Remote Receiver Pressure Testing Fireplace Gas ConnectionsRemoving Glass Door Replace battery cover onto remote control unitRemoving/Replacing Glass Door Removing Louver PanelsCleaning Glass Door Installing lava rock and glowing embersInstalling Brick liner Models BL42DASA and BL42DHASA Replace screen/rod assembly by reversing stepClose top and bottom louvers For your safety Read before lightingOperating Fireplace Lighting InstructionsTo Turn OFF GAS To Appliance Manual Lighting Procedure Optional Hand-HeldRemote Operation Thermostat Series Model HRC200 On/Off Series Model HRC100Inspecting Burners Operating optional blower accessoryPilot assembly Key Pad Lock FeatureCleaning Maintenance Burner Flame PatternGlass Door Pilot and burners LogsVenting system Observed Problem Possible Cause Remedy TroubleshootingLong enough Control knob pressed Problem could be caused by Replace pilot assemblyBurner orifice clogged Clean burner see Cleaning Is lit After pilot lights, keep gasCold Minute Air in gas line Operate burner until air is When burner is lit HI position when burner isTery power is low Turning gas control knob toStatement above Gas leak. See WarningSpecifications Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown Parts List 19 18 116236-01G Burner Pan Assembly Accessories Wall mounted on/off switch Wall mounted thermostat control kit gwmt1GwmS2 Not Shown Warranty Information Keep this WarrantyLimited Warranty DIRECT-VENT Fireplace