Desa (V)VC42P, CGCDV42NR, CGCDV42PR installation manual Pilot and burners, Logs, Venting system

Page 32

Cleaning and

Maintenance

Continued

CAUTION: Do not vacuum if pieces are hot.

Use only the tempered glass door replacement intended for this fireplace (see Replacement Parts, page 37 for detail on ordering). No substitutions may be made. See Removing/Replacing Glass Door, page 25 for instructions for replacing glass door.

WARNING: Do not operate fireplace with the glass door unlatched, removed, cracked or broken.

Pilot and burners

Remove ember material before cleaning burners and replace when cleaning is complete.

Burner and controls should be cleaned with compressed air to remove dust, dirt or lint.

Use a vacuum cleaner or small, soft bristled brush to remove excess dust, dirt or lint.

Logs

If you remove logs for cleaning, refer to Install- ing Lava Rock and Glowing Embers, page 26, to properly replace logs.

Use a vacuum cleaner to remove any carbon buildup on logs.

Replace log(s) if broken. See Replacement Parts on page 37.

Replace ember material periodically as needed. See Replacement Parts on page 37.

venting system

Conduct annual inspection of the venting system following these guidelines:

1.Check areas of venting system that are ex- posed to the weather for corrosion (rust spots or streaks and, in extreme cases, holes). Have these items replaced immediately by a quali- fied service person.

2.Remove the vent cap and shine a flashlight into the vent. Remove any foreign material.

3.Check for evidence of excessive condensation. Continuous condensation can cause corrosion of caps, pipes and fittings and can be caused by having excessive lateral runs, too many elbows or exterior portions of the system being exposed to cold weather.

4.Inspect joints to verify that no pipe section or fitting has been disturbed and loosened. Check mechanical supports such as wall straps for rigidity.

32

www.desatech.com

116236-01G

Image 32
Contents What to do if YOU Smell GAS Patent PendingTable of Contents Safety InformationSafety Information High traffic areas Product IdentificationLocal Codes Product Features Pre-Installation PreparationLocation and space requirements This fireplace does not require electricity to operateClearances Minimum clearances to combustibles for42 1067 mm Front 36 914 mm Top of Standoffs VentFireplace Framing and finishingNoncombustible mantels at any height above Location of Termination Cap Balcony with Perpendicular Side WallVenting Installation Instructions Installation PrecautionsInstallation Planning Installing Horizontal Vent Cap Noncombustible Exterior Ground Floor Installation Round TerminationCorner Installation Recommended Applications Corner ground floor installationHorizontal System Installation Using TWO 90 Elbows Connect a section of pipe and extend up through the hole Installation for vertical terminationFlat Ceiling Installation Twist-lock the vent cap onto the last section of vent pipe High Altitude Installation Vertical VentingParts list for venting kits and components Desa 5/8 Pipe & Vent Kits Number DescriptionFireplace Installation Installing optional blower accessoriesModel BK Installation Plug in blower power cordModel BKT Installation Blower Model BKTInstallation Items Needed Installing Gas Piping to Fireplace LocationBlower Wiring Diagram Connecting Fireplace to GAS Supply Propane/LP FromChecking GAS Connections Test Pressures Equal To or Less Than Psig 3.5 kPaPressure Testing Fireplace Gas Connections Installing Remote ReceiverReplace battery cover onto remote control unit Removing/Replacing Glass DoorRemoving Louver Panels Removing Glass DoorInstalling lava rock and glowing embers Installing Brick liner Models BL42DASA and BL42DHASAReplace screen/rod assembly by reversing step Cleaning Glass DoorFor your safety Read before lighting Operating FireplaceLighting Instructions Close top and bottom louversRemote Operation To Turn OFF GAS To Appliance Manual Lighting ProcedureOptional Hand-Held On/Off Series Model HRC100 Thermostat Series Model HRC200Operating optional blower accessory Pilot assemblyKey Pad Lock Feature Inspecting BurnersGlass Door Cleaning MaintenanceBurner Flame Pattern Venting system Pilot and burnersLogs Troubleshooting Observed Problem Possible Cause RemedyProblem could be caused by Replace pilot assembly Burner orifice clogged Clean burner see Cleaning Is litAfter pilot lights, keep gas Long enough Control knob pressedWhen burner is lit HI position when burner is Tery power is lowTurning gas control knob to Cold Minute Air in gas line Operate burner until air isGas leak. See Warning Statement aboveReplacement Parts Service HintsTechnical Service SpecificationsIllustrated Parts Breakdown Parts List 19 18 116236-01G Burner Pan Assembly Accessories GwmS2 Not Shown Wall mounted on/off switchWall mounted thermostat control kit gwmt1 Limited Warranty DIRECT-VENT Fireplace Warranty InformationKeep this Warranty