Invacare manual Using the Powered Seating Switch, Using the Four Way Switch, Right

Page 25

SECTION 5—WHEELCHAIR OPERATION

Using the Powered Seating Switch

NOTE: The powered seating switch will alternate functions (increase tilt angle, decrease tilt angle) after it has been released for a minimum of three seconds.

1.Make sure the wheelchair is on a level surface.

2.Press the powered seating switch once to activate the actuator.

3.Press the powered seating switch again (after at least 3 seconds) to activate the actuator in the opposite direction.

Using the Four Way Switch

NOTE: For this procedure, refer to FIGURE 5.1 on page 26.

1.Make sure the wheelchair is on a level surface.

2.Refer to the chart for the operation of the seating system using a four way switch.

NOTE: The chart shows the factory programmed settings only. Switch assignments can be reprogrammed.

	SEATING SYSTEM		FOUR WAY SWITCH

		FORWARD	REAR	LEFT	RIGHT
		FORWARD	REAR	LEFT	RIGHT

	Formula TRE - Tilt Only	Decrease the Tilt	Increase the Tilt	N/A	N/A
		Angle	Angle

	Formula TRE - Recline	Decrease the	Increase the Recline	Power Legrest Up/	Power Legrest Up/
	Only	Recline Angle	Angle	Down*	Down*

	Formula TRE - Tilt/Recline	Decrease the	Increase the Recline	Decrease the Tilt	Increase the Tilt
		Recline Angle	Angle	Angle	Angle

	Formula TRE - Elevate	N/A	N/A	Elevate/Lower the	N/A
	Only**			Seat*

	Formula TRE - Tilt/Elevate	Increase/Decrease	N/A	Elevate/Lower the	N/A
		the Tilt Angle*		Seat*

	Formula TRE -	Increase/Decrease	Increase/Decrease	Elevate/Lower the	Power Legrest Up/
	Tilt/Recline/Elevate	the Tilt Angle*	the Recline Angle*	Seat*	Down*

*NOTE: The four-way switch will alternate functions (increase tilt angle, decrease tilt angle) after it has been released to the neutral position for a minimum of three seconds.

**NOTE: The seat MUST be tilted/reclined so the back angle is less than 20° relative to the vertical position before elevating/lowering the seat.

NOTE: If the wheelchair is equipped with switch options, scan to the correct ECU or Auxiliary Mode and activate the control device in the corresponding "forward" direction to operate the tilt function. Refer to the electronics manual for complete switch option operating instructions.

3. Release four way switch to neutral position.

Part No 1122170

25

Formula™ Powered Seating

Image 25

Contents Dealer This manual Must be given to the user of the product Formula Powered SeatingReference Documents Reference DocumentsDocument Part Number Table of Contents Register Your Product Special Notes Signal Word MeaningWheelchair TIE-DOWN Restraints and Seat Restraints Trbkts Powered Seating System Warnings All Wheelchairs Label LocationsWheelchairs with Elevate Wheelchairs with Ventilator Trays Typical Product Parameters Formula Powered Seating SystemsContoura Backs Conventional Backs Typical Product Parameters Contoura Backs ConventionalGeneral Guidelines Repair or Service InformationOperation Information General Guidelines General Guidelines Weight Limitation Weight TrainingEMI Information EMI InformationEMI Information Pinch Points SAFETY/HANDLING of WheelchairsSafety Inspection Checklists Safety INSPECTION/ TroubleshootingInspect/Adjust Initially Inspect/Adjust Monthly Inspect/Adjust WeeklyInspect/Adjust Periodically Symptom Probable Cause Solutions TroubleshootingJS REV TOO Large Tilt Warning displays Wheelchair Operation System Type Joystick Powered Seating Control Operating Powered Seating SystemsSwitch Option Through Using the Four Way Switch Using the Powered Seating SwitchSeating System Four WAY Switch RightIcon Description Using the MPJ+ joystickUsing the MPJ+ joystick Drive Select Toggle Switch MPJ+ Joystick Switches and IndicatorsSpeed Control Charger/Programming Input JoystickLCD Display Screens LCD Display ECU Remote On/Off Switch Programmable Mono Port 1/2 or External Mode SwitchWheelchair Operation Icon Preparing the Joystick for Use Mode SwitchMemory Card Slot Repositioning the Joystick Front Riggings Installing/Removing FootrestsPHAL4A, 70 and PW93 Taper Footrest Height AdjustmentPHAL4A Front Riggings PW93 Footrest Height Adjustment PW93Raising/Lowering Elevating Front Riggings Adjusting/Replacing Telescoping Front Rigging SupportAdjusting/Replacing Telescoping Front Rigging Support Installing Adjustable Angle Flip-up Footplates Installing Adjustable Angle Flip-up Footplate HingeDepth Adjustment Adjusting Adjustable Angle Flip-Up FootplatesAngle Adjustment Perpendicular and/or Inversion/Eversion AdjustmentDisassembly Composite/Articulating Footplate Heel Loop ReplacementAssembly Installing Installing/Removing Elevating LegrestsRemoving Raising/Lowering Elevating Legrests Adjusting CalfpadsRemoving/Installing the Center Mount Footrest 15 Removing/Installing the Center Mount Footrest 16 Adjusting the Height of the Center Mount Footrest Adjusting the Height of the Center Mount FootrestAdjusting the Footplate Angle Adjusting the Angle of the Manual Center Mount FootrestAfter 2/14/07 Before 2/15/07 Adjusting the Tension of the Flip Up Footplate21 Calf Pad Adjustment for Power Center Mount Footrests Calf Pad Adjustment for Power Center Mount FootrestsHeight and Width Adjustment Installing/Removing the Power Elevating LegrestsInstalling the Power Elevating Legrests 22 Installing/Removing the Power Elevating Legrests Removing the Power Elevating LegrestsArms Installing/Removing Flip Back ArmrestsAdjusting Adjusting Flip Back ArmrestsPositioning Flip Back Armrests for User Transfer Positioning Flip Back Armrests for UseInstalling Armrests Removing/Installing Reclining ArmrestsRemoving Armrests Adjusting Reclining Armrest Height Adjusting Reclining Armrest Height Seat Adjusting the Back AngleReplacing Seat Positioning Strap Replacing Seat Positioning StrapHeadrest Removing/Installing/Adjusting HeadrestAdjusting Headrest Depth/Direction Adjusting Headrest HeightReplacing Headrest Elevate Batteries Replacing Batteries Using the Proper BatteriesElevate Batteries Replacing Batteries Removing/Installing the Batteries From/Into the Wheelchair Cleaning Battery TerminalsRemoving the Battery Door and Rear Shrouds ImmediatelyRemoving the Battery Door and Rear Shrouds Removing the Batteries Installing BatteriesInstalling Batteries Installing the Battery Door and Rear ShroudCharging Batteries When to Charge BatteriesTool Quantity Comments Description and Use of Battery ChargersCharging Batteries Preparing the Ventilator Tray for Use Ventilator TrayPreparing the Ventilator Tray for Use Global Limited Warranty Excluding Canada Global Limited Warranty Excluding CanadaUSA Canada Limited Warranty