4.3Weight and Measurement Specifications (142 Settings)
To configure weight and measurement specifications, press and hold the REZERO key and enter 142 using the numeric keypad. SPC20 appears in WEIGHT display and configuration of four bits (for SPEC 20) appears in QUANTITY display. Follow the procedure described in Section 4.1 on page 17 to update the SPEC settings for the 142 access code.
SPEC | Default |
| Bit 3 |
|
|
| Bit 2 |
|
| Bit 1 |
| Bit 0 | |
|
|
|
|
|
|
| |||||||
20 | none | Minimum Display (PORT 1, Scale 1) |
| Minimum Display (PORT 1, Scale 2) | |||||||||
|
| MUST BE SET PRIOR TO CALIBRATION! |
| MUST BE SET PRIOR TO CALIBRATION! | |||||||||
|
| 00: | 2 | 01: | 1 |
|
|
| 00: | 2 | 01: | 1 |
|
|
| 10: | 5 | 11: | 10 |
|
|
| 10: | 5 | 11: | 10 |
|
|
|
|
|
|
| ||||||||
21 | none | Eltron Printer Selection | Weight Decimal Point Position (PORT 1, Scale 1) |
| |||||||||
|
| 0: | Eltron Model 2722 | MUST BE SET PRIOR TO CALIBRATION! |
|
| |||||||
|
| 1: | Eltron Model 2742 | 000: 00000 | 011: 00.000 |
|
|
| |||||
|
|
| or 2642 |
|
| 001: 0000.0 | 100: 0.0000 |
|
|
| |||
|
| NOTE: Must be set to | 010: 000.00 | 101: .00000 |
|
|
| ||||||
|
| 0 if an Eltron printer is |
|
|
|
|
|
|
|
| |||
|
| not being used. |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| |||||||
22 | none | Not used |
|
| Weight Decimal Point Position (PORT 1, Scale 2) |
| |||||||
|
|
|
|
|
| MUST BE SET PRIOR TO CALIBRATION! |
|
| |||||
|
|
|
|
|
| 000: 00000 | 011: 00.000 |
|
|
| |||
|
|
|
|
|
| 001: 0000.0 | 100: 0.0000 |
|
|
| |||
|
|
|
|
|
| 010: 000.00 | 101: .00000 |
|
|
| |||
|
|
|
|
|
|
| |||||||
23 | 0000 | Display Resolution for Scales 1, 2, 3, and 4. |
| Zero Setting Range |
| ||||||||
|
| (Specify Not Used for force balance.) |
| 00: | 01: ±2% FS | ||||||||
|
|
|
|
|
|
|
|
| |||||
|
| 00: 1/10000 |
| 01: 1/5000 |
| 10: ±10% FS |
| 11: Not used | |||||
|
| 10: 1/2500 |
| 11: Not used |
|
|
|
|
|
| |||
|
|
|
|
|
|
| |||||||
24 | 0000 | Masked Display at |
| Display at Minus Weight | Zero Lamp Lighting | Low Battery (turn off | |||||||
|
| Minus Weight |
|
| 0: | Minus display |
| Method |
|
| display when low battery) | ||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| 0: | Gross |
|
| 1: | Masked |
| 0: | Gross |
|
| 0: No |
|
| 1: | Net |
|
|
|
|
| 1: | Net |
|
| 1: Yes |
|
|
|
|
|
|
|
|
| |||||
25 | 00_0 | Scale Starting Method | Internal Resolution |
| Scale Type |
|
| Gross Mode Available | |||||
|
| 0: | Automatic |
| Protected by Span |
| 0: | Single scale |
| 0: Yes (allows gross | |||
|
|
| Switch |
|
| ||||||||
|
| 1: | Manual (must |
|
| 1: | Dual scale |
| mode selection from | ||||
|
|
|
|
|
|
| |||||||
|
|
| press REZERO key | 0: | No (internal |
| NOTE: If you are not | keypad) | |||||
|
|
| on startup) |
|
| resolution can be | 1: No (inhibits gross | ||||||
|
|
|
|
| connected to a |
| |||||||
|
|
|
|
|
|
| viewed by pressing |
| mode; switching not | ||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| REZERO * * +) |
| allowed) | ||||
|
|
|
|
|
|
|
| do not have two scales | |||||
|
|
|
|
|
| 1: | Yes (protected until |
| |||||
|
|
|
|
|
| wired into Cable PORT |
| ||||||
|
|
|
|
|
|
| internal span |
|
| ||||
|
|
|
|
|
|
|
| 1, set this bit to 0 (single |
| ||||
|
|
|
|
|
|
| switch pressed) |
|
| ||||
|
|
|
|
|
|
|
| scale). Selecting 1 (dual |
| ||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| scale) can damage the |
| |||
|
|
|
|
|
|
|
|
| console’s electronic |
| |||
|
|
|
|
|
|
|
|
| components. |
|
|
| |
|
|
|
|
|
|
|
| ||||||
26 | 0000 | Zero Tracking When | Rezero with a Tare |
| Initial Start Range |
|
| ||||||
|
| Tare Is Present |
| Weight |
| 00: | 01: ±2% FS | ||||||
|
|
|
|
|
|
|
|
| |||||
|
| 0: Yes |
|
| 0: Yes |
| 10: ±10% FS |
| 11: Not used | ||||
|
| 1: No (zero tracking is | 1: No |
|
|
|
|
|
| ||||
|
| off with tare in system) |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|