BenQ SP920P Connecting a Hdmi source device, To connect the projector to a Hdmi source device

Page 19

Connecting a HDMI source device

The projector provides a HDMI input socket that allows you to connect it to a HDMI source device like a DVD player, a DTV tuner or a display.

HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players and displays over a single cable. It provides pure digital viewing and listening experience.

Examine your source device to determine if it has an unused HDMI output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a HDMI source device:

1.Take a HDMI cable and connect one end to the HDMI output socket of the HDMI source device. Connect the other end of the cable to the HDMI signal input socket on the projector.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio Settings" on page 44 for details.

•In the unlikely event that

AV device	you connect the projector
	to a DVD player and the
	projected picture displays
	wrong colors, please
	change the color space to
	YUV. See "Changing Color
	Space" on page 27 for
	details.
1	• If no signal is detected after
HDMI	establishing the
cable	connection, turn off the
	Quick Auto Search function
	in the SOURCE menu. See
	"Switching input signal" on
	page 27 for details.

English

Connection 19

Image 19

Contents SP920P Digital Projector WelcomeTable of contents 3000 m 10000 feet Important safety instructionsWith all windows rolled up Cigarette smoke may contaminate opticalImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Projector Controls and functionsMute ModeOperating the projector from the front Remote control effective rangeMaking the remote control a wired control Operating the Laser pointerChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Better video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceWith a Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device With a Component Video cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationSecuring the projector Using the On-Screen Display OSD menusUsing a security cable lock Use / to highlight the System Setup Basic menuTo leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the passwordConfirm the new password by re-entering the new password Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode PC input signals D-Sub/Comp. analog RGB and DVI-D DVI-DFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Follow these steps to utilize this function Setting the presentation timerRepeat steps 3 to 6 for other color adjustments Press MENU/EXIT to exit and save the settingsUsing the OSD menu To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW key? Using the remote controlFreezing the image Utilizing FAQ functionPossible solutions To exit the OSD menu, press MENU/EXIT Hiding the imageOperating in a high altitude environment Press / or go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Locking control keysCreating your own startup screen Adjusting the soundAdjusting the sound level Turning off the Power on/off ring tonePersonalizing the On-Screen Display OSD menus Setting the lamp modeShutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Advanced Setup BasicDescription of each menu Sleep Timer Presentation TimerAuto Power Off Blank TimerFAQ-Image Installation Lamp SettingsSecurity Settings Reset All SettingsCare of the projector MaintenanceLamp information Timing of replacing the lamp Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Extending lamp lifeScrewdriver Remove the lamp cover from the projector Replacing the lampWay into the projector Resetting the corresponding lamp timerGo to the System Setup Advanced Lamp Settings menu Restart the projectorIndicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for Video and S-Video inputs Timing chartSupported timing for Analog RGB input Supported timing for Component-YPbPrinputFrequency kHz Frequency Hz MHz ResolutionHorizontal Vertical Pixel Frequency Mode Supported timing for DVI-D and Hdmi Hdcp inputRegulation statements Other informationEnglish