BenQ SP920P Projector exterior view, Front/upper side Rear/lower side, RGB signal output socket

Page 8

English

Projector exterior view

Front/upper side

	4
1
	5
2	6
	6
3	7
3

Rear/lower side

See "Connection" on page 16 for connection details.

13

14

15

16

17

18

19

20

21

22

23

24

25

8

	9	9
	9
		26
	10	12
	11	12
	11

9

12

9

1.Lamp cover

2.Vent (heated air exhaust)

3.Projection lens

4.External control panel (See page 9 for details.)

5.Focus ring and Zoom ring (See page 9 for details.)

6.Vent (cool air intake)

7.Front IR remote sensor

8.AC power cord inlet

9.Adjuster feet

10.Kensington anti-theft lock slot

11.Speaker grill

12.Ceiling mount holes

13.Rear IR remote sensor

14.Wired remote control port

15.Audio signal input socket

16.RS232 control port

17.USB socket

18.HDMI port

19.DVI-D signal input socket

20.RGB (PC)/Component Video (YPbPr/ YCbCr) signal input socket

21.DC 12V output terminal

Used to trigger external devices such as an electric screen or light control, etc. Consult your dealer for how to connect these devices.

22.RGB signal output socket

23.Component Video (YPbPr/ YCbCr) signal input sockets

24.S-Video signal input socket

25.Composite Video signal input socket

26.Vent (heated air exhaust)

8 Introduction

Image 8

Contents Welcome SP920P Digital ProjectorTable of contents Important safety instructions With all windows rolled upCigarette smoke may contaminate optical 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Projector features IntroductionShipping contents Front/upper side Rear/lower side RGB signal output socketProjector exterior view Controls and functions ProjectorMode MuteRemote control effective range Making the remote control a wired controlOperating the Laser pointer Operating the projector from the frontPositioning your projector Choosing a locationObtaining a preferred projected image size Select your screen size Projection dimensions ZoomConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerWith a VGA cable With a VGA to DVI-A cable Connecting a monitorTo connect the projector to a monitor Connecting Video source devices Connecting AudioBest video quality Better video qualityConnecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a DVI-D source device To connect the projector to a DVI-D source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cableConnecting an S-Video or a composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorUsing the On-Screen Display OSD menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Confirm the new password by re-entering the new passwordSwitching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioUsing Wall Color Selecting a picture modePC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Adjusting Brilliant ColorSelecting a color temperature Setting the presentation timer Repeat steps 3 to 6 for other color adjustmentsPress MENU/EXIT to exit and save the settings Follow these steps to utilize this functionTo cancel the timer, perform the following steps How to use the Timer ON/SHOW key?Using the remote control Using the OSD menuUtilizing FAQ function Possible solutions To exit the OSD menu, press MENU/EXITHiding the image Freezing the imagePress / or go to the System Setup Basic Panel Key Lock To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Creating your own startup screenSetting the lamp mode Personalizing the On-Screen Display OSD menusShutting down the projector Main menu Sub-menu Options On-Screen Display OSD MenusMenu structure Setup Basic AdvancedDescription of each menu Presentation Timer Auto Power OffBlank Timer Sleep TimerLamp Settings Security SettingsReset All Settings FAQ-Image InstallationLamp information MaintenanceCare of the projector Setting Lamp Mode as Dual-Reliable Setting Auto Power OffExtending lamp life Timing of replacing the lampReplacing the lamp Screwdriver Remove the lamp cover from the projectorResetting the corresponding lamp timer Go to the System Setup Advanced Lamp Settings menuRestart the projector Way into the projectorIndicators Troubleshooting Dimensions SpecificationsProjector specifications Timing chart Supported timing for Analog RGB inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsResolution Horizontal Vertical Pixel Frequency ModeSupported timing for DVI-D and Hdmi Hdcp input Frequency kHz Frequency Hz MHzOther information Regulation statementsEnglish