BenQ SP920P user manual Other information, Regulation statements

Page 55

Other information

Warranty and Copyright information

Limited warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be in-between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright

Copyright 2008 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

Regulation statements

FCC statement

CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

EEC statement

This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electronic Magnetic Compatibility) and fulfills these requirements.

WEEE directive

Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union.

This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment. For more information about recycling of this equipment, please contact your city office, the shop where you purchased the equipment or your household waste disposal service. The recycling of materials will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and environment.

English

Other information

55

Image 55
Contents SP920P Digital Projector WelcomeTable of contents 3000 m 10000 feet Important safety instructionsWith all windows rolled up Cigarette smoke may contaminate opticalImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Projector Controls and functionsMute ModeOperating the projector from the front Remote control effective rangeMaking the remote control a wired control Operating the Laser pointerChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Better video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceWith a Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device With a Component Video cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationSecuring the projector Using the On-Screen Display OSD menusUsing a security cable lock Use / to highlight the System Setup Basic menuTo leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the passwordConfirm the new password by re-entering the new password Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode PC input signals D-Sub/Comp. analog RGB and DVI-D DVI-DFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Follow these steps to utilize this function Setting the presentation timerRepeat steps 3 to 6 for other color adjustments Press MENU/EXIT to exit and save the settingsUsing the OSD menu To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW key? Using the remote controlFreezing the image Utilizing FAQ functionPossible solutions To exit the OSD menu, press MENU/EXIT Hiding the imageOperating in a high altitude environment Press / or go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Locking control keysCreating your own startup screen Adjusting the soundAdjusting the sound level Turning off the Power on/off ring tonePersonalizing the On-Screen Display OSD menus Setting the lamp modeShutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Advanced Setup BasicDescription of each menu Sleep Timer Presentation TimerAuto Power Off Blank TimerFAQ-Image Installation Lamp SettingsSecurity Settings Reset All SettingsCare of the projector MaintenanceLamp information Timing of replacing the lamp Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Extending lamp lifeScrewdriver Remove the lamp cover from the projector Replacing the lampWay into the projector Resetting the corresponding lamp timerGo to the System Setup Advanced Lamp Settings menu Restart the projectorIndicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for Video and S-Video inputs Timing chartSupported timing for Analog RGB input Supported timing for Component-YPbPrinputFrequency kHz Frequency Hz MHz ResolutionHorizontal Vertical Pixel Frequency Mode Supported timing for DVI-D and Hdmi Hdcp inputRegulation statements Other informationEnglish