BenQ SP920P user manual Magnifying and searching for details, Correcting keystone

Page 29
The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.

Correcting keystone

Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.

To correct this, besides adjusting the height of the projector, you will need to manually correct it by following one of these steps.

•Using the remote control

Press / on the control panel of the projector or remote

control to display the Keystone correction page. Press to correct

keystoning at the top of the image. Press to correct keystoning at the bottom of the image.

• Using the OSD menu

1. Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Keystone and press ENTER. The Keystone

correction page displays.

Keystone

3.Press to correct keystoning at the top of the image or press

to correct keystoning at the bottom of the image.

Press / .

Press / .

MENU Back

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

•Using the remote control

1.Press D. ZOOM +/- to display the Zoom bar.

2.Press D. ZOOM + to magnify the center of the picture. Press the

key repeatedly until the picture size is suitable for your need.

3.Use the directional arrows ( , , , ) on the projector or

remote control to navigate the picture.

4. To restore the picture to its original size, press AUTO. You can also press D. ZOOM -. When the key is pressed again, the picture is further reduced until it is restored to the original size.

•Using the OSD menu

1. Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2. Press to highlight Digital Zoom and press ENTER. The Zoom bar displays.

3. Repeat steps 2-4in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps.

4.Press on the projector repeatedly to magnify the picture to a desired size.

5.To navigate the picture, press ENTER to switch to the paning

mode and press the directional arrows ( , , , ) to navigate the picture.

6.To reduce size of the picture, press ENTER to switch back to the zoom in/out function, and press AUTO to restore the picture to

its original size. You can also press repeatedly until it is restored to the original size.

English

Operation 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents SP920P Digital Projector WelcomeTable of contents With all windows rolled up Important safety instructionsCigarette smoke may contaminate optical 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side RGB signal output socketProjector exterior view Projector Controls and functionsMute ModeMaking the remote control a wired control Remote control effective rangeOperating the Laser pointer Operating the projector from the frontChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerWith a VGA cable With a VGA to DVI-A cable Connecting a monitorTo connect the projector to a monitor Connecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationUsing a security cable lock Using the On-Screen Display OSD menusUse / to highlight the System Setup Basic menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MENU/EXITChanging the password Entering the password recall procedureDisabling the password function Confirm the new password by re-entering the new passwordChanging Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioSelecting a picture mode Using Wall ColorPC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Adjusting Brilliant ColorSelecting a color temperature Repeat steps 3 to 6 for other color adjustments Setting the presentation timerPress MENU/EXIT to exit and save the settings Follow these steps to utilize this functionHow to use the Timer ON/SHOW key? To cancel the timer, perform the following stepsUsing the remote control Using the OSD menuPossible solutions To exit the OSD menu, press MENU/EXIT Utilizing FAQ functionHiding the image Freezing the imageTo activate the High Altitude Mode Press / or go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Creating your own startup screenPersonalizing the On-Screen Display OSD menus Setting the lamp modeShutting down the projector Main menu Sub-menu Options On-Screen Display OSD MenusMenu structure Advanced Setup BasicDescription of each menu Auto Power Off Presentation TimerBlank Timer Sleep TimerSecurity Settings Lamp SettingsReset All Settings FAQ-Image InstallationLamp information MaintenanceCare of the projector Setting Auto Power Off Setting Lamp Mode as Dual-ReliableExtending lamp life Timing of replacing the lampScrewdriver Remove the lamp cover from the projector Replacing the lampGo to the System Setup Advanced Lamp Settings menu Resetting the corresponding lamp timerRestart the projector Way into the projectorIndicators Troubleshooting Dimensions SpecificationsProjector specifications Supported timing for Analog RGB input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsHorizontal Vertical Pixel Frequency Mode ResolutionSupported timing for DVI-D and Hdmi Hdcp input Frequency kHz Frequency Hz MHzRegulation statements Other informationEnglish
Top Page Image Contents