BenQ SP920P user manual Connecting an S-Video or a composite Video source device

Page 22

English

Connecting an S-Video or a composite Video source device

Examine your Video source device to determine if it has an unused S-Video or Video output socket available:

•If it has both sockets, use the S-Video output socket for connection as the S-Video terminal provides better picture quality than the Video terminal. See "Connecting Video source devices" on page 18 for details.

•If it has either of the output socket, you can also continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as this makes an unnecessary second connection of poorer picture quality. You need only connect using a composite Video connection if both Component Video and S-Video are not supplied on the video source device (for example, with some analog video cameras).

To connect the projector to an S-Video/Video source device:

1.Take an S-Video/Video cable and connect one end to the S-Video/Video output socket of the Video source device.

2.Connect the other end of the S-Video/Video cable to the S-VIDEO/VIDEOsocket on the projector.

3.If you wish to make use of the projector (mixed mono) speakers in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the AUDIO socket of the projector.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio

Settings" on page 44 for details.

The final connection path should be like that shown in the following diagram:

AV device

31. Video cable

1. S-Video cable

3. Audio cable

•The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting Audio" on page 18 for details.

•If the selected video image

 

 

is not displayed after the

1

or 1

projector is turned on and

the correct video source

 

 

 

 

has been selected, check

 

 

that the Video source

 

 

device is turned on and

 

 

operating correctly. Also

 

 

check that the signal cables

 

 

have been connected

 

 

correctly.

22 Connection

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Welcome SP920P Digital ProjectorTable of contents Cigarette smoke may contaminate optical Important safety instructionsWith all windows rolled up 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Controls and functions ProjectorMode MuteOperating the Laser pointer Remote control effective rangeMaking the remote control a wired control Operating the projector from the frontPositioning your projector Choosing a locationObtaining a preferred projected image size Select your screen size Projection dimensions ZoomConnection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Best video quality Connecting Video source devicesConnecting Audio Better video qualityConnecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a DVI-D source device To connect the projector to a DVI-D source deviceWith a Component Video cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device With a Component Video to VGA D-Sub adaptor cableConnecting an S-Video or a composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorUse / to highlight the System Setup Basic menu Using the On-Screen Display OSD menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MENU/EXITDisabling the password function Entering the password recall procedureChanging the password Confirm the new password by re-entering the new passwordSwitching input signal Changing Color SpaceAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioPC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Using Wall ColorSelecting a picture mode Optimizing the imageFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Press MENU/EXIT to exit and save the settings Setting the presentation timerRepeat steps 3 to 6 for other color adjustments Follow these steps to utilize this functionUsing the remote control To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW key? Using the OSD menuHiding the image Utilizing FAQ functionPossible solutions To exit the OSD menu, press MENU/EXIT Freezing the imageLocking control keys Press / or go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Operating in a high altitude environmentTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Creating your own startup screenSetting the lamp mode Personalizing the On-Screen Display OSD menusShutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Setup Basic AdvancedDescription of each menu Blank Timer Presentation TimerAuto Power Off Sleep TimerReset All Settings Lamp SettingsSecurity Settings FAQ-Image InstallationCare of the projector MaintenanceLamp information Extending lamp life Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Timing of replacing the lampReplacing the lamp Screwdriver Remove the lamp cover from the projectorRestart the projector Resetting the corresponding lamp timerGo to the System Setup Advanced Lamp Settings menu Way into the projectorIndicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for Component-YPbPrinput Timing chartSupported timing for Analog RGB input Supported timing for Video and S-Video inputsSupported timing for DVI-D and Hdmi Hdcp input ResolutionHorizontal Vertical Pixel Frequency Mode Frequency kHz Frequency Hz MHzOther information Regulation statementsEnglish
Top Page Image Contents