BenQ SP920P user manual Shipping contents

Page 7

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

*The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.

	(UK)	(US) (KOREA)	(CHINA)
		(AU)	(JAPAN)
			(JAPAN)
		(EU)
Projector	Power cord		VGA cable	Remote control with
				batteries

English

Quick start guide	Multi-language user	User manual	Warranty card*
	manual CD

Optional accessories

If you need to purchase the accessories listed below, please also contact your local dealer.

1.	Spare lamp kit	3.	Presentation Plus
2.	Ceiling mount kit	4.	RS232 cable

Installing or replacing the remote control batteries

1. To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it up in the direction of the arrow as illustrated. The cover will slide off.

2. Remove any existing batteries (if necessary) and install two

AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.

3.Refit the cover by aligning it with the base and sliding it back down into position. Stop when it clicks into place.

•Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

•Replace only with the same or equivalent type recommended by the battery manufacturer.

•Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.

•Never throw the batteries into a fire. There may be danger of an explosion.

•If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.

Introduction 7

Image 7

Contents SP920P Digital Projector WelcomeTable of contents 3000 m 10000 feet Important safety instructionsWith all windows rolled up Cigarette smoke may contaminate opticalImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Projector Controls and functionsMute ModeOperating the projector from the front Remote control effective rangeMaking the remote control a wired control Operating the Laser pointerChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Better video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceWith a Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device With a Component Video cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationSecuring the projector Using the On-Screen Display OSD menusUsing a security cable lock Use / to highlight the System Setup Basic menuTo leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the passwordConfirm the new password by re-entering the new password Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode PC input signals D-Sub/Comp. analog RGB and DVI-D DVI-DFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Follow these steps to utilize this function Setting the presentation timerRepeat steps 3 to 6 for other color adjustments Press MENU/EXIT to exit and save the settingsUsing the OSD menu To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW key? Using the remote controlFreezing the image Utilizing FAQ functionPossible solutions To exit the OSD menu, press MENU/EXIT Hiding the imageOperating in a high altitude environment Press / or go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Locking control keysCreating your own startup screen Adjusting the soundAdjusting the sound level Turning off the Power on/off ring tonePersonalizing the On-Screen Display OSD menus Setting the lamp modeShutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Advanced Setup BasicDescription of each menu Sleep Timer Presentation TimerAuto Power Off Blank TimerFAQ-Image Installation Lamp SettingsSecurity Settings Reset All SettingsCare of the projector MaintenanceLamp information Timing of replacing the lamp Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Extending lamp lifeScrewdriver Remove the lamp cover from the projector Replacing the lampWay into the projector Resetting the corresponding lamp timerGo to the System Setup Advanced Lamp Settings menu Restart the projectorIndicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for Video and S-Video inputs Timing chartSupported timing for Analog RGB input Supported timing for Component-YPbPrinputFrequency kHz Frequency Hz MHz ResolutionHorizontal Vertical Pixel Frequency Mode Supported timing for DVI-D and Hdmi Hdcp inputRegulation statements Other informationEnglish