BenQ SP920P user manual On-Screen Display OSD Menus, Menu structure, Main menu Sub-menu Options

Page 41

On-Screen Display (OSD) Menus

Menu structure

Please note that the on-screen display (OSD) menus vary according to the signal type selected. Some functions are available only when certain input signals are in use.

The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Main menu	Sub-menu	Options
	Wall Color	Off/Light Yellow/Pink/Light Green/
	Wall Color	Blue/Blackboard
		Blue/Blackboard
	Aspect Ratio	4:3/16:9/Auto/Real

1.Keystone

DISPLAY Position Phase H. Size Digital Zoom

				PC source: Dynamic/Presentation/sRGB/Cinema/User 1/
		Picture Mode		User 2
				Video source: Dynamic/Standard/Cinema/User 1/User 2
		Reference Mode		PC source: Dynamic/Presentation/sRGB/Cinema
		Reference Mode		Video source: Dynamic/Standard/Cinema
				Video source: Dynamic/Standard/Cinema
		Brightness
		Contrast
	2.	Color
	2.	Tint
	PICTURE	Tint
	PICTURE	Sharpness
		Sharpness
		Brilliant Color			On/Off
		Color Temperature			T1/T2/T3/T4
		3D Color		Primary Color	R/G/B/Y/C/M
		3D Color		Hue
		Management		Saturation
				Gain
		Save Settings
	3. SOURCE	Quick Auto Search			On/Off
	3. SOURCE	Color Space Conversion			RGB/YUV
		Color Space Conversion			RGB/YUV

			FAQ-Image and Installation
			FAQ-Features and Service
					•	Source
	6.				•	Picture Mode
	INFORMATION		Current System Status		•	Resolution
	INFORMATION				•	Color System
					•	Color System
					•	Lamp Mode
					•	Equivalent Lamp #1 Hour
					•	Equivalent Lamp #2 Hour

English

Operation 41

Image 41

Contents SP920P Digital Projector WelcomeTable of contents With all windows rolled up Important safety instructionsCigarette smoke may contaminate optical 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side RGB signal output socketProjector exterior view Projector Controls and functionsMute ModeMaking the remote control a wired control Remote control effective rangeOperating the Laser pointer Operating the projector from the frontChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerWith a VGA cable With a VGA to DVI-A cable Connecting a monitorTo connect the projector to a monitor Connecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationUsing a security cable lock Using the On-Screen Display OSD menusUse / to highlight the System Setup Basic menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MENU/EXITChanging the password Entering the password recall procedureDisabling the password function Confirm the new password by re-entering the new passwordChanging Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioSelecting a picture mode Using Wall ColorPC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Adjusting Brilliant ColorSelecting a color temperature Repeat steps 3 to 6 for other color adjustments Setting the presentation timerPress MENU/EXIT to exit and save the settings Follow these steps to utilize this functionHow to use the Timer ON/SHOW key? To cancel the timer, perform the following stepsUsing the remote control Using the OSD menuPossible solutions To exit the OSD menu, press MENU/EXIT Utilizing FAQ functionHiding the image Freezing the imageTo activate the High Altitude Mode Press / or go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Creating your own startup screenPersonalizing the On-Screen Display OSD menus Setting the lamp modeShutting down the projector Main menu Sub-menu Options On-Screen Display OSD MenusMenu structure Advanced Setup BasicDescription of each menu Auto Power Off Presentation TimerBlank Timer Sleep TimerSecurity Settings Lamp SettingsReset All Settings FAQ-Image InstallationLamp information MaintenanceCare of the projector Setting Auto Power Off Setting Lamp Mode as Dual-ReliableExtending lamp life Timing of replacing the lampScrewdriver Remove the lamp cover from the projector Replacing the lampGo to the System Setup Advanced Lamp Settings menu Resetting the corresponding lamp timerRestart the projector Way into the projectorIndicators Troubleshooting Dimensions SpecificationsProjector specifications Supported timing for Analog RGB input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsHorizontal Vertical Pixel Frequency Mode ResolutionSupported timing for DVI-D and Hdmi Hdcp input Frequency kHz Frequency Hz MHzRegulation statements Other informationEnglish