BenQ SP920P Important safety instructions, With all windows rolled up, 3000 m 10000 feet

Page 3

Thank you for your purchase of this quality BenQ projector! It has been designed to provide you with an enjoyable viewing experience in various situations. For the best results, please read this manual through carefully as it is your guide through the control menus and operation.

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

1.

Please read this manual before you operate 4.

Do not place this projector in any of the

 

your projector. Save it for future reference.

following environments.

 

 

- Space that is poorly ventilated or confined.

 

 

Allow at least 50 cm clearance from walls

 

 

and free flow of air around the projector.

 

 

- Locations where temperatures may become

 

 

excessively high, such as the inside of a car

 

 

with all windows rolled up.

 

 

- Locations where excessive humidity, dust, or

 

 

cigarette smoke may contaminate optical

2.

Do not look straight at the projector lens

components, shortening the projector's life

span and darkening the image.

 

during operation. The intense light beam may

 

 

damage your eyes.

3. Refer servicing to qualified service

 

personnel.

- Locations near fire alarms

 

 

- Locations with an ambient temperature

 

above 40°C / 104°F

 

- Locations where the altitudes are higher than

 

3000 m (10000 feet)

English

3000 m

(10000 feet)

0m

(0 feet)

Important safety instructions

3

Image 3
Contents SP920P Digital Projector WelcomeTable of contents 3000 m 10000 feet Important safety instructionsWith all windows rolled up Cigarette smoke may contaminate opticalImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents RGB signal output socket Projector exterior viewFront/upper side Rear/lower side Projector Controls and functionsMute ModeOperating the projector from the front Remote control effective rangeMaking the remote control a wired control Operating the Laser pointerChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting a monitor To connect the projector to a monitorWith a VGA cable With a VGA to DVI-A cable Better video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceWith a Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device With a Component Video cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationSecuring the projector Using the On-Screen Display OSD menusUsing a security cable lock Use / to highlight the System Setup Basic menuTo leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the passwordConfirm the new password by re-entering the new password Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode PC input signals D-Sub/Comp. analog RGB and DVI-D DVI-DFine-tuning the image quality in user modes Adjusting Brilliant Color Selecting a color temperature3D Color Management Follow these steps to utilize this function Setting the presentation timerRepeat steps 3 to 6 for other color adjustments Press MENU/EXIT to exit and save the settingsUsing the OSD menu To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW key? Using the remote controlFreezing the image Utilizing FAQ functionPossible solutions To exit the OSD menu, press MENU/EXIT Hiding the imageOperating in a high altitude environment Press / or go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Locking control keysCreating your own startup screen Adjusting the soundAdjusting the sound level Turning off the Power on/off ring tonePersonalizing the On-Screen Display OSD menus Setting the lamp modeShutting down the projector On-Screen Display OSD Menus Menu structureMain menu Sub-menu Options Advanced Setup BasicDescription of each menu Sleep Timer Presentation TimerAuto Power Off Blank TimerFAQ-Image Installation Lamp SettingsSecurity Settings Reset All SettingsMaintenance Care of the projectorLamp information Timing of replacing the lamp Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Extending lamp lifeScrewdriver Remove the lamp cover from the projector Replacing the lampWay into the projector Resetting the corresponding lamp timerGo to the System Setup Advanced Lamp Settings menu Restart the projectorIndicators Troubleshooting Specifications Projector specificationsDimensions Supported timing for Video and S-Video inputs Timing chartSupported timing for Analog RGB input Supported timing for Component-YPbPrinputFrequency kHz Frequency Hz MHz ResolutionHorizontal Vertical Pixel Frequency Mode Supported timing for DVI-D and Hdmi Hdcp inputRegulation statements Other informationEnglish