BenQ SP920P Resetting the corresponding lamp timer, Restart the projector, Way into the projector

Page 49

7.Lift the handle so that it stands up. Use the handle 12. Replace the lamp cover on the projector. to slowly pull the lamp out of the projector.

1

2

 

13.

Tighten the screw that secures the lamp cover.

Pulling it too quickly may cause the lamp to

 

 

break and scatter broken glass in the

 

 

projector.

 

 

Do not place the lamp in locations where

 

 

water might splash on it, children can reach

 

 

it, or near flammable materials.

 

 

Do not insert your hands into the projector

 

 

after the lamp is removed. If you touch the

 

 

optical components inside, it could cause

 

 

color unevenness and distortion of the

 

Loose screw may cause a bad connection,

projected pictures.

 

8. As shown in the figure, hold the new lamp and

 

which could result in malfunction.

 

Do not over tighten the screw.

align the two locators on the lamp with the holes

 

 

 

on the projector, and then insert the lamp all the

14.

Restart the projector.

way into the projector.

 

Do not turn the power on with the lamp cover

 

 

removed.

English

9.Tighten the screw that secures the lamp.

10.Connect the lamp connector to the projector and tighten the screw that secures the lamp connector.

Resetting the corresponding lamp timer

15.After the startup logo, open the On-Screen Display (OSD) menu.

Go to the SYSTEM SETUP: Advanced > Lamp Settings menu.

Press ENTER and the Lamp Settings page displays.

Highlight Reset Lamp #1 Timer/Reset Lamp #2 Timer. A warning message displays asking if you want to reset the lamp timer.

Highlight Reset and press ENTER on the projector or remote control. The lamp time will be reset to '0'.

Notice

Reset Lamp #1 Timer

Reset Cancel

Loose screw may cause a bad connection,

which could result in malfunction.Do not reset if the lamp is not new or replaced as this could cause damage.

Do not over tighten the screw.

11.Ensure the handle is fully laid flat and locked in place.

Maintenance 49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents SP920P Digital Projector WelcomeTable of contents With all windows rolled up Important safety instructionsCigarette smoke may contaminate optical 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Projector Controls and functionsMute ModeMaking the remote control a wired control Remote control effective rangeOperating the Laser pointer Operating the projector from the frontChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Connecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationUsing a security cable lock Using the On-Screen Display OSD menusUse / to highlight the System Setup Basic menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MENU/EXITChanging the password Entering the password recall procedureDisabling the password function Confirm the new password by re-entering the new passwordChanging Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioSelecting a picture mode Using Wall ColorPC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Optimizing the imageFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Repeat steps 3 to 6 for other color adjustments Setting the presentation timerPress MENU/EXIT to exit and save the settings Follow these steps to utilize this functionHow to use the Timer ON/SHOW key? To cancel the timer, perform the following stepsUsing the remote control Using the OSD menuPossible solutions To exit the OSD menu, press MENU/EXIT Utilizing FAQ functionHiding the image Freezing the imageTo activate the High Altitude Mode Press / or go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Creating your own startup screenPersonalizing the On-Screen Display OSD menus Setting the lamp modeShutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Advanced Setup BasicDescription of each menu Auto Power Off Presentation TimerBlank Timer Sleep TimerSecurity Settings Lamp SettingsReset All Settings FAQ-Image InstallationCare of the projector MaintenanceLamp information Setting Auto Power Off Setting Lamp Mode as Dual-ReliableExtending lamp life Timing of replacing the lampScrewdriver Remove the lamp cover from the projector Replacing the lampGo to the System Setup Advanced Lamp Settings menu Resetting the corresponding lamp timerRestart the projector Way into the projectorIndicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for Analog RGB input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsHorizontal Vertical Pixel Frequency Mode ResolutionSupported timing for DVI-D and Hdmi Hdcp input Frequency kHz Frequency Hz MHzRegulation statements Other informationEnglish
Top Page Image Contents