BenQ SP920P user manual Maintenance, Care of the projector, Lamp information

Page 46

English

Maintenance

Care of the projector

Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface.

Use a canister of compressed air to remove dust.

If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.

Never rub the lens with abrasive materials.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as described in "Shutting down the projector" on page 40 and unplug the power cord.

To remove dirt or dust, wipe the case with a soft, lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications" on page 52 or consult your dealer about the range.

Retract the adjuster feet.

Remove the batteries from the remote control.

Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent. When you carry the projector yourself, please use the original box or a suitable soft carry case.

Lamp information

Getting to know the lamp hour

When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows:

Total (equivalent) lamp hour

=1 (hours used in Dual-Reliable mode) + 3/2 (hours used in Dual-Brightest mode) + 3/2 (hours used in Single- Alternative mode)

See "Setting the lamp mode" on page 39 below for more information.

To obtain the lamp hour information:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Lamp Settings and press ENTER. The Lamp Settings page displays.

3.You will see the Equivalent Lamp #1 Hour/Equivalent Lamp #2 Hour information displaying on the menu.

4.To leave the menu, press MENU/EXIT.

You can also get the lamp hour information on the INFORMATION menu.

46 Maintenance

Image 46
Contents Welcome SP920P Digital ProjectorTable of contents Cigarette smoke may contaminate optical Important safety instructionsWith all windows rolled up 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Controls and functions ProjectorMode MuteOperating the Laser pointer Remote control effective rangeMaking the remote control a wired control Operating the projector from the frontPositioning your projector Choosing a locationObtaining a preferred projected image size Select your screen size Projection dimensions ZoomConnection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Best video quality Connecting Video source devicesConnecting Audio Better video qualityConnecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a DVI-D source device To connect the projector to a DVI-D source deviceWith a Component Video cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device With a Component Video to VGA D-Sub adaptor cableConnecting an S-Video or a composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorUse / to highlight the System Setup Basic menu Using the On-Screen Display OSD menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MENU/EXITDisabling the password function Entering the password recall procedureChanging the password Confirm the new password by re-entering the new passwordSwitching input signal Changing Color SpaceAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioPC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Using Wall ColorSelecting a picture mode Optimizing the imageFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Press MENU/EXIT to exit and save the settings Setting the presentation timerRepeat steps 3 to 6 for other color adjustments Follow these steps to utilize this functionUsing the remote control To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW key? Using the OSD menuHiding the image Utilizing FAQ functionPossible solutions To exit the OSD menu, press MENU/EXIT Freezing the imageLocking control keys Press / or go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Operating in a high altitude environmentTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Creating your own startup screenSetting the lamp mode Personalizing the On-Screen Display OSD menusShutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Setup Basic AdvancedDescription of each menu Blank Timer Presentation TimerAuto Power Off Sleep TimerReset All Settings Lamp SettingsSecurity Settings FAQ-Image InstallationCare of the projector MaintenanceLamp information Extending lamp life Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Timing of replacing the lampReplacing the lamp Screwdriver Remove the lamp cover from the projectorRestart the projector Resetting the corresponding lamp timerGo to the System Setup Advanced Lamp Settings menu Way into the projectorIndicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for Component-YPbPrinput Timing chartSupported timing for Analog RGB input Supported timing for Video and S-Video inputsSupported timing for DVI-D and Hdmi Hdcp input ResolutionHorizontal Vertical Pixel Frequency Mode Frequency kHz Frequency Hz MHzOther information Regulation statementsEnglish