BenQ SP920P user manual Specifications, Projector specifications, Dimensions

Page 52

English

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

1024 x 768 XGA

Display system 1-CHIP DMD

Lens F/Number

F=2.4 to 2.55, f=23.88 to 27.46 mm

Lamp

280 W lamp x 2

Electrical

Power supply

AC 100–240 V, 7.7 A, 50-60 Hz (Automatic)

Power consumption

805 W (Max); 5 W (Standby)

Mechanical

Weight 11 kg

Output terminals

RGB output

D-Sub 15-pin (female) x 1

Speaker

(Stereo) 5 watt x 2 12 VDC (Max. 1 A)

Control

USB serial control

Type mini B

RS-232 serial control

Mini Din 8 pin x 1

Dimensions

443.0mm (W) x 167.0 mm (H) x 355.0 mm (D)

355.0

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 1 DVI-D input

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3, D-Sub 15-pin

Digital - DVI-D (supports HDCP) Digital - HDMI

Audio signal input Audio in

PC audio jack x 1

Wire remote

2.5 mm wire jack

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C

1500–3000 m at 0°C–30°C (with High Altitude Mode on)

443.0

167.0

63.85 85.50

52 Specifications

Image 52

Contents Welcome SP920P Digital ProjectorTable of contents Important safety instructions With all windows rolled upCigarette smoke may contaminate optical 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Controls and functions ProjectorMode MuteRemote control effective range Making the remote control a wired controlOperating the Laser pointer Operating the projector from the frontPositioning your projector Choosing a locationObtaining a preferred projected image size Select your screen size Projection dimensions ZoomConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Connecting Video source devices Connecting AudioBest video quality Better video qualityConnecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a DVI-D source device To connect the projector to a DVI-D source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cableConnecting an S-Video or a composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorUsing the On-Screen Display OSD menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Confirm the new password by re-entering the new passwordSwitching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioUsing Wall Color Selecting a picture modePC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Optimizing the imageFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Setting the presentation timer Repeat steps 3 to 6 for other color adjustmentsPress MENU/EXIT to exit and save the settings Follow these steps to utilize this functionTo cancel the timer, perform the following steps How to use the Timer ON/SHOW key?Using the remote control Using the OSD menuUtilizing FAQ function Possible solutions To exit the OSD menu, press MENU/EXITHiding the image Freezing the imagePress / or go to the System Setup Basic Panel Key Lock To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Creating your own startup screenSetting the lamp mode Personalizing the On-Screen Display OSD menusShutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Setup Basic AdvancedDescription of each menu Presentation Timer Auto Power OffBlank Timer Sleep TimerLamp Settings Security SettingsReset All Settings FAQ-Image InstallationCare of the projector MaintenanceLamp information Setting Lamp Mode as Dual-Reliable Setting Auto Power OffExtending lamp life Timing of replacing the lampReplacing the lamp Screwdriver Remove the lamp cover from the projectorResetting the corresponding lamp timer Go to the System Setup Advanced Lamp Settings menuRestart the projector Way into the projectorIndicators Troubleshooting Projector specifications SpecificationsDimensions Timing chart Supported timing for Analog RGB inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsResolution Horizontal Vertical Pixel Frequency ModeSupported timing for DVI-D and Hdmi Hdcp input Frequency kHz Frequency Hz MHzOther information Regulation statementsEnglish