Invacare Ranger II250 SERIES, Ranger IIJR, Ranger IISTANDARD, Ranger IIBASIC Shrouds Procedure

SHROUDS PROCEDURE 10

FWD Wheelchairs (FIGURE 2)

REMOVING FRONT SHROUD.

1.Unclip the retaining strap securing the front shroud and battery box to the wheelchair.

2.Feed the retaining strap through the front shroud.

3.Remove the front shroud from the wheelchair.

INSTALLING FRONT SHROUD.

1.Feed the retaining strap through the front shroud as shown in FIGURE 2.

2.Position the bottom of the front shroud between the battery box and the battery tray.

3.Clip the retaining strap together.

4.Pull end of retaining strap to secure front battery box and front shroud in place.

REMOVING REAR SHROUD.

1.Perform one (1) of the following:

A.For 16,18, and 20-inch wide chairs:

l Unclip the retaining strap securing the rear shroud and battery box to the wheelchair.

l Feed the retaining strap through the rear shroud.

l Remove the rear shroud from the wheelchair.

B.For 14-inch wide chairs:

l Lift up on rear shroud and remove from wheel- chair.

INSTALLING REAR SHROUD.

1.Perform one (1) of the following:

A.For 16,18, and 20-inch wide chairs:

l Feed the retaining strap through the rear shroud as shown in FIGURE 2.

l Clip the retaining strap together.

l Press down on the rear shroud until the two

(2)clips secure the rear shroud to the two (2) side shrouds.

lPull end of retaining strap to secure rear bat- tery box and shroud in place.

B.For 14-inch wide chairs:

lAlgin clips of rear shroud with tabs on side shrouds.

lPress down on rear shroud until the two clips and dual lock fastener secure the rear shroud in place.

REMOVING SIDE SHROUDS AND FILLERS.

1.Remove the front shroud from the wheelchair. Refer toREMOVING/INSTALLINGFRONTSHROUDinthis procedure of the manual.

2.Remove the rear shroud from the wheelchair. Refer to REMOVING/INSTALLING REAR SHROUD in this procedure of the manual.

3.Perform one (1) of the following:

A.INTEGRATED SLING SEAT MODELS - Fold the wheelchair. Referto TRANSPORTINGRANGER II FWD in PROCEDURE 12 of this manual.

B.CAPTAIN'S SEAT MODELS - Remove the Captain's Seat from the wheelchair. Refer to RE- MOVING/INSTALLINGCAPTAIN'SSEATinPRO- CEDURE 5 of the owner's manual, part number 1080722.

4.HIGH BACK CAPTAIN'S SEAT MODEL WHEEL- CHAIRSONLY(DETAIL"A")-Remove the phono jack nut that secures the phono jack to the side shroud.

5.Remove the phillips screws, bolts, washers and lock- nuts that secure side shroud and filler to the wheel- chair frame. Refer to FIGURE 2 for phillips screw and washer locations.

6.Remove side shroud and filler from the wheelchair.

7.Repeat STEPS 5-6 for the opposite side of the wheel- chair, if necessary.

INSTALLING SIDE SHROUDS AND FILLERS.

1.Position side shroud and filler on the wheelchair frame.

2.Line up the mounting holes in the side shroud and filler with the mounting holes in the wheelchair frame.

CAUTION

DO NOT overtighten the phillips screws and phillips bolt that secure the side shroud to the wheelchair frame - oth- erwise damage to the side shroud can occur.

3.Install the phillips screws, bolts, washers and lock- nuts that secure the side shroud and filler to the wheel- chair frame and tighten securely. DO NOT OVER- TIGHTEN. Refer to FIGURE 2 for phillips screw, bolt, washer and locknut locations.

4.Repeat STEPS 1-3 for the opposite side of the wheel- chair, if necessary.

5.HIGH BACK CAPTAIN'S SEAT MODEL WHEEL- CHAIRS ONLY - If necessary, perform the following:

A.Position the phono jack on the side shroud.

B.Reinstall the phono jack nut onto the phono jack and tighten securely.

S H R O U D S

35