SpectraLink 150 M3 MCU manual Pull Cable, Terminate Cable at Base Station Locations

Page 19

SpectraLink Corporation

Link WTS Installation and Operation

4.2Pull Cable

Pull the cable from the MCU location (usually in the telephone equipment room) to the Base Station locations designated on the floor plans.

If the cabling exits the building, consult the telephone system manual, the NEC, and local codes for instructions on providing lightning and other over- current protection.

When cabling an external Base Station or a Base Station with wiring that exits the building, protect all Base Station wiring with the Quick Clip Fuse (Illinois Tool Works, Linx Division, SCP-2X2) before bridging with other Base Station power leads.

Run all cable before attaching the RJ-45 connectors to the Base Stations. Label both the demarcation block end and the Base Station end of each wire with the Base Station number using a wire tie marker or other form of marker.

Remove bridge taps, multiples, or "Y" connections to the Base Station wires;

!these will cause data transmission errors.

The area above some suspended ceilings is used as an environmental air plenum. The National Electric Code requires that wire installed in plenums be rated for plenum installation.

4.3Terminate Cable at Base Station Locations

After running the wire to the Base Station location, terminate the wire using an RJ-45 modular crimp-on plug. Connect the data pair to pins 1 and 2 and the power pair to pins 7 and 8.

If the connection uses more than two pair, refer to the table on the following page.

! To avoid damage to the connectors or crimps, be sure to run the wire to the Base Station before connecting the RJ-45 connectors.

RJ-45 Modular Cable

Part Number: 72-0075-01-C-W.doc

Page 8

Image 19
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Icons and Conventions Installation OverviewAbout This Document Questions?SpectraLink Corporation Link WTS Installation and Operation System Operation Link Wireless Telephone System OverviewSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Required Materials Site PreparationDetermine Location of MCU Run Cable for System Wire SpecificationsRun Cables to Base Station Locations Terminate Cable at Base Station Locations Pull CableMCU Prepare Demarc BlocksDedicated Line for Diagnostic Modem Multiple Power PairsTwo Wire Analog or Digital Interface Four Wire Digital Interface Assign and Program Ports Install Demarc BlocksSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Survey Site Install Link Wireless Telephone SystemCheck Components Mount MCUs to Wall Install MCUsConnect MCU to Demarc Blocks Connect Multi-Unit Systems Connect PowerSet Switch Interface Type Switch Interface Line LEDs MCU Type Mount Base Stations on Dropped Tile Ceilings Install Base StationsMount Base Stations On Finished Ceilings Wire and Connect Outdoor Base Stations Install Outdoor Base StationsSet Up Diagnostic Modem Connect and Register Wireless TelephonesRegister Wireless Telephones Unregister Wireless Telephones Test Wireless Telephones Program Wireless Telephone FeaturesSite Certification Troubleshoot Error Codes System AdministrationTroubleshoot Phone Features Status LEDs Description Action 12345 Status LED CodesStatus Description Action LEDs Status Description Action LEDs Indicator Description Action Wireless Telephone Status Indicator MessagesDelete Old Wireless Telephone Replace a Wireless TelephoneRegister New Wireless Telephone Connect the Replacement MCU Clear Configuration on Replacement MCUReplace an MCU Replace a Base Station MCU ID Wireless Telephone Planning WorksheetBase Station Location Worksheet Select Alternate Spread Spectrum Sequence Appendix a Technical ParametersChange Companding Open Application Interface Appendix B Program Analog FeaturesDefining Macros Plan ProgrammingProgram Macro Codes Clear or Erase a Function Examples of ProgrammingTransfer Speed DialBefore Installing the OAI Telephony Gateway Mount Telephony Gateway to Wall OAI Telephony Gateway’s Front PanelInitial Test Connect the OAI Telephony Gateway to the MCU Assign a Function Key to OAI Telephony Gateway Connect the OAI Telephony Gateway to the Application ServerCertification Test LED IndexOAI