SpectraLink 150 M3 MCU manual Unregister Wireless Telephones

Page 38

SpectraLink Corporation

Link WTS Installation and Operation

To register a Wireless Telephone to your system do the following:

1.Be sure all unregistered Wireless Telephones are powered off and that there is a Base Station plugged in and within range of the Wireless Telephones to be registered.

2.Move the mode switch to the REGISTER position. (If your system has more than one MCU, be sure to move the switch only on the correct MCU.) The LED which indicates the Box ID (1-4) may change. This is normal and is not an error.

The Line Indicator LEDs now show the registration status of each line.

If the LED is on, a Wireless Telephone is registered to the line.

If the LED is off, no Wireless Telephone is registered to the line.

3.Press the STEP button until the LED for the line to be registered flashes.

If the LED is flashing, that line is selected. A flash with the LED mainly off indicates no Wireless Telephone registered; a flash with the LED mainly on indicates a Wireless Telephone is registered to the selected line.

Initially Line 2 will flash. This is because Line 1 is usually set up as the remote access diagnostic modem. To register a Wireless Telephone to Line 1, press the STEP button until Line 1 flashes.

If the desired line already has a Wireless Telephone registered to it, follow the procedure outlined below to unregister the Wireless Telephone, then return to this step.

4.Turn on the Wireless Telephone to be registered by holding down the PWR key until the Wireless Telephone beeps twice. After a few seconds, the line indicator LED on the MCU will shine solid red. Once the Wireless Telephone is registered, the LED for the next line begins to flash.

5.To assign the extension number, hold down the FCN key until Volume Level displays. Press the # > key (NEXT) until EXTENSION displays on the Wireless Telephone. Press 0, then enter the correct extension number. Press END when finished.

6.Repeat steps 3-5 for all Wireless Telephones to be registered.

7.When all Wireless Telephones are registered, return the mode switch to the NORM position.

6.3Unregister Wireless Telephones

If the desired line already has a Wireless Telephone registered to it, follow this procedure to unregister the Wireless Telephone.

1.Move the mode switch on the MCU to the REGISTER position. If your system has more than one MCU, be sure to move the switch on the correct MCU. The line indicator LEDs now show which lines have Wireless Telephones registered.

2.Use the STEP button to select the line to be unregistered. The line indicator LED for a line that has a Wireless Telephone registered to it will flash with the LED

Part Number: 72-0075-01-C-W.doc

Page 27

Image 38
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Questions? Installation OverviewAbout This Document Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation Link Wireless Telephone System Overview System OperationSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Determine Location of MCU Site PreparationRequired Materials Run Cables to Base Station Locations Wire SpecificationsRun Cable for System Pull Cable Terminate Cable at Base Station LocationsPrepare Demarc Blocks MCUMultiple Power Pairs Dedicated Line for Diagnostic ModemTwo Wire Analog or Digital Interface Four Wire Digital Interface Install Demarc Blocks Assign and Program PortsSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Check Components Install Link Wireless Telephone SystemSurvey Site Connect MCU to Demarc Blocks Install MCUsMount MCUs to Wall Connect Power Connect Multi-Unit SystemsSet Switch Interface Type Switch Interface Line LEDs MCU Type Install Base Stations Mount Base Stations on Dropped Tile CeilingsMount Base Stations On Finished Ceilings Install Outdoor Base Stations Wire and Connect Outdoor Base StationsRegister Wireless Telephones Connect and Register Wireless TelephonesSet Up Diagnostic Modem Unregister Wireless Telephones Program Wireless Telephone Features Test Wireless TelephonesSite Certification Troubleshoot Phone Features System AdministrationTroubleshoot Error Codes Status LED Codes Status LEDs Description Action 12345Status Description Action LEDs Status Description Action LEDs Wireless Telephone Status Indicator Messages Indicator Description ActionRegister New Wireless Telephone Replace a Wireless TelephoneDelete Old Wireless Telephone Replace an MCU Clear Configuration on Replacement MCUConnect the Replacement MCU Replace a Base Station Wireless Telephone Planning Worksheet MCU IDBase Station Location Worksheet Appendix a Technical Parameters Select Alternate Spread Spectrum SequenceChange Companding Plan Programming Appendix B Program Analog FeaturesDefining Macros Open Application InterfaceProgram Macro Codes Speed Dial Examples of ProgrammingTransfer Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway OAI Telephony Gateway’s Front Panel Mount Telephony Gateway to WallInitial Test Connect the OAI Telephony Gateway to the MCU Connect the OAI Telephony Gateway to the Application Server Assign a Function Key to OAI Telephony GatewayCertification Test Index LEDOAI