SpectraLink 150 M3 MCU manual SpectraLink Corporation Link WTS Installation and Operation

Page 3

SpectraLink Corporation

Link WTS Installation and Operation

Note concerning the Master Control Unit:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note concerning shielded cable:

SpectraLink recommends the use of shielded cable for all external signal connections in order to maintain FCC Part 15 emissions requirements.

Note concerning the Wireless Telephone and Base Stations:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) t his device must accept any interference received, including interference that may cause undesired operation.

WARNING Changes or modifications to this equipment not approved by SpectraLink Corporation may cause this equipment to not comply with part 15 of the FCC rules and void the user’s authority to operate this equipment.

WARNING SpectraLink products contain no user -serviceable parts inside. Refer servicing to qualified service personnel.

Part Number: 72-0075-01-C-W.doc

Page iii

Image 3
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Icons and Conventions Installation OverviewAbout This Document Questions?SpectraLink Corporation Link WTS Installation and Operation System Operation Link Wireless Telephone System OverviewSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Site Preparation Required MaterialsDetermine Location of MCU Wire Specifications Run Cable for SystemRun Cables to Base Station Locations Terminate Cable at Base Station Locations Pull CableMCU Prepare Demarc BlocksDedicated Line for Diagnostic Modem Multiple Power PairsTwo Wire Analog or Digital Interface Four Wire Digital Interface Assign and Program Ports Install Demarc BlocksSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Install Link Wireless Telephone System Survey SiteCheck Components Install MCUs Mount MCUs to WallConnect MCU to Demarc Blocks Connect Multi-Unit Systems Connect PowerSet Switch Interface Type Switch Interface Line LEDs MCU Type Mount Base Stations on Dropped Tile Ceilings Install Base StationsMount Base Stations On Finished Ceilings Wire and Connect Outdoor Base Stations Install Outdoor Base StationsConnect and Register Wireless Telephones Set Up Diagnostic ModemRegister Wireless Telephones Unregister Wireless Telephones Test Wireless Telephones Program Wireless Telephone FeaturesSite Certification System Administration Troubleshoot Error CodesTroubleshoot Phone Features Status LEDs Description Action 12345 Status LED CodesStatus Description Action LEDs Status Description Action LEDs Indicator Description Action Wireless Telephone Status Indicator MessagesReplace a Wireless Telephone Delete Old Wireless TelephoneRegister New Wireless Telephone Clear Configuration on Replacement MCU Connect the Replacement MCUReplace an MCU Replace a Base Station MCU ID Wireless Telephone Planning WorksheetBase Station Location Worksheet Select Alternate Spread Spectrum Sequence Appendix a Technical ParametersChange Companding Open Application Interface Appendix B Program Analog FeaturesDefining Macros Plan ProgrammingProgram Macro Codes Clear or Erase a Function Examples of ProgrammingTransfer Speed DialBefore Installing the OAI Telephony Gateway Mount Telephony Gateway to Wall OAI Telephony Gateway’s Front PanelInitial Test Connect the OAI Telephony Gateway to the MCU Assign a Function Key to OAI Telephony Gateway Connect the OAI Telephony Gateway to the Application ServerCertification Test LED IndexOAI