SpectraLink 150 M3 MCU manual Before Installing the OAI Telephony Gateway

Page 56

SpectraLink Corporation

Link WTS Installation and Operation

13. Appendix C: Installing the Open

Applications Interface (OAI) Telephony

Gateway

The OAI Telephony Gateway (MOG 500) allows the Link 150 M3 MCU to interface with an application server as shown in the diagram belo w. This enables third-party applications to communicate directly with the Link 150 M3 MCU, allowing users to retrieve and respond to information using Wireless Telephones. A single OAI Telephony Gateway can be connected to a Link 150 Master Control Unit (MCU) using an IPC cable (8-conductor cable with RJ-45 connectors)..

		Application
		Server
IPC bus	RS-232	(PC)
Link 150 MCU	Link	or
Link 150 MCU	OAI Gateway	Modem
		Modem

13.1 Before Installing the OAI Telephony Gateway

If this is a new system installation, secure the OAI Telephony Gateway to the wall, power up and test the Telephony Gateway when the MCUs are tested. Connect the OAI Telephony Gateway to the MCU after the Base Stations are installed.

If you are adding the OAI Telephony Gateway to an existing system, the system will need to be shut down and re-set to install the OAI Telephony Gateway. Notify users that the system will be out of service during the installation.

Part Number: 72-0075-01-C-W.doc

Page 45

Image 56

Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Installation Overview About This DocumentQuestions? Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation Link Wireless Telephone System Overview System OperationSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Determine Location of MCU Site PreparationRequired Materials Run Cables to Base Station Locations Wire SpecificationsRun Cable for System Pull Cable Terminate Cable at Base Station LocationsPrepare Demarc Blocks MCUMultiple Power Pairs Dedicated Line for Diagnostic ModemTwo Wire Analog or Digital Interface Four Wire Digital Interface Install Demarc Blocks Assign and Program PortsSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Check Components Install Link Wireless Telephone SystemSurvey Site Connect MCU to Demarc Blocks Install MCUsMount MCUs to Wall Connect Power Connect Multi-Unit SystemsSet Switch Interface Type Switch Interface Line LEDs MCU Type Install Base Stations Mount Base Stations on Dropped Tile CeilingsMount Base Stations On Finished Ceilings Install Outdoor Base Stations Wire and Connect Outdoor Base StationsRegister Wireless Telephones Connect and Register Wireless TelephonesSet Up Diagnostic Modem Unregister Wireless Telephones Program Wireless Telephone Features Test Wireless TelephonesSite Certification Troubleshoot Phone Features System AdministrationTroubleshoot Error Codes Status LED Codes Status LEDs Description Action 12345Status Description Action LEDs Status Description Action LEDs Wireless Telephone Status Indicator Messages Indicator Description ActionRegister New Wireless Telephone Replace a Wireless TelephoneDelete Old Wireless Telephone Replace an MCU Clear Configuration on Replacement MCUConnect the Replacement MCU Replace a Base Station Wireless Telephone Planning Worksheet MCU IDBase Station Location Worksheet Appendix a Technical Parameters Select Alternate Spread Spectrum SequenceChange Companding Appendix B Program Analog Features Defining MacrosPlan Programming Open Application InterfaceProgram Macro Codes Examples of Programming TransferSpeed Dial Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway OAI Telephony Gateway’s Front Panel Mount Telephony Gateway to WallInitial Test Connect the OAI Telephony Gateway to the MCU Connect the OAI Telephony Gateway to the Application Server Assign a Function Key to OAI Telephony GatewayCertification Test Index LEDOAI