SpectraLink 150 M3 MCU manual FCC Information

Page 5

SpectraLink Corporation

Link WTS Installation and Operation

FCC Information

The Master Control Unit Complies with Part 68, FCC Rules

FCC Registration Numbers:

Link 150: IYGUSA -33400-PX-E

Ringer Equivalence:

Link 150 Model 3: 0.3B

SpectraLink Corporation

Link 150

Made in the USA

This equipment complies with Part 68 of the FCC Rules. On the back of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be given to the telephone company.

This equipment uses RJ -21 connectors.

The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. In most, but not all, areas, the sum of the RENs of all devices connected to one line should not exceed five (5.0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone company to determine the maximum REN for your calling area.

If your telephone equipment causes harm to the telephone network, the telephone service may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice isn’t practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.

Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.

If you experience trouble with this telephone equipment, please contact: SpectraLink Corporation

5755 Central Avenue

Boulder, CO 80301 303-440-5330

for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. There are no user serviceable parts in this equipment.

This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.

Part Number: 72-0075-01-C-W.doc

Page v

Image 5
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration About This Document Installation OverviewQuestions? Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation System Operation Link Wireless Telephone System OverviewSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Determine Location of MCU Site PreparationRequired Materials Run Cables to Base Station Locations Wire SpecificationsRun Cable for System Terminate Cable at Base Station Locations Pull CableMCU Prepare Demarc BlocksDedicated Line for Diagnostic Modem Multiple Power PairsTwo Wire Analog or Digital Interface Four Wire Digital Interface Assign and Program Ports Install Demarc BlocksSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Check Components Install Link Wireless Telephone SystemSurvey Site Connect MCU to Demarc Blocks Install MCUsMount MCUs to Wall Connect Multi-Unit Systems Connect PowerSet Switch Interface Type Switch Interface Line LEDs MCU Type Mount Base Stations on Dropped Tile Ceilings Install Base StationsMount Base Stations On Finished Ceilings Wire and Connect Outdoor Base Stations Install Outdoor Base StationsRegister Wireless Telephones Connect and Register Wireless TelephonesSet Up Diagnostic Modem Unregister Wireless Telephones Test Wireless Telephones Program Wireless Telephone FeaturesSite Certification Troubleshoot Phone Features System AdministrationTroubleshoot Error Codes Status LEDs Description Action 12345 Status LED CodesStatus Description Action LEDs Status Description Action LEDs Indicator Description Action Wireless Telephone Status Indicator MessagesRegister New Wireless Telephone Replace a Wireless TelephoneDelete Old Wireless Telephone Replace an MCU Clear Configuration on Replacement MCUConnect the Replacement MCU Replace a Base Station MCU ID Wireless Telephone Planning WorksheetBase Station Location Worksheet Select Alternate Spread Spectrum Sequence Appendix a Technical ParametersChange Companding Defining Macros Appendix B Program Analog FeaturesPlan Programming Open Application InterfaceProgram Macro Codes Transfer Examples of ProgrammingSpeed Dial Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway Mount Telephony Gateway to Wall OAI Telephony Gateway’s Front PanelInitial Test Connect the OAI Telephony Gateway to the MCU Assign a Function Key to OAI Telephony Gateway Connect the OAI Telephony Gateway to the Application ServerCertification Test LED IndexOAI