SpectraLink 150 M3 MCU manual Customer Responsibilities Return Material Authorization

Page 8

SpectraLink Corporation

Link WTS Installation and Operation

Customer Responsibilities

Return Material Authorization

1.Maintain the installation site and provide the necessary utility services for use of the Product in accordance with SpectraLink’s applicable published specifications, see installation guide.

2.Provide all on-site labor necessary to assist SpectraLink in troubleshooting; and for receiving, replacing, and returning all parts required to effect a repair.

3.Provide unattended dial-up modem access to the system for remote diagnosis by SpectraLink service personnel.

4.Customer will return to SpectraLink all defective equipment for which an advanced shipment replacement has been made within ten business days. Failure to return replaced items within the above-referenced period will result in a customer obligation to pay full purchase price for the replacement item.

All equipment failures must be verified by a SpectraLink Customer Support representative and assigned a Return Material Authorization (RMA) number. Replacement equipment will not be shipped without an RMA number assigned. Equipment received by SpectraLink without an RMA number will be returned to the customer without being repaired.

Exclusions

Termination

The following services are not included under this Agreement:

1.Support of Products not listed under the Coverage section above.

2.On-site services performed by SpectraLink to effect repair.

3.Services required to repair Product which has been opened, disassembled, or otherwise tampered with due to unauthorized attempts by persons other than SpectraLink employees or persons authorized by SpectraLink to install, repair, maintain, or modify the hardware or software.

4.Services required due to causes external to the SpectraLink maintained Products including, but not limited to fire, flood, lightning, physical abuse, immersion in liquids, or exposure to solvents.

5.Services in connection with the relocation of the Product, or the addition, removal, or maintenance of other devices not furnished by SpectraLink, including communications devices, networks, or links.

SpectraLink requires 30-days written notice to cancel any optional services purchased to upgrade the SpectraLink Warranty Support. Such written notice must be on company stationary and indicate the date on which the cancellation is to be effective. SpectraLink will credit the customer any unused prepaid maintenance fees, calculated on a pro rata basis.

Part Number: 72-0075-01-C-W.doc

Page viii

Image 8
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Installation Overview About This DocumentQuestions? Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation Link Wireless Telephone System Overview System OperationSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Determine Location of MCU Site PreparationRequired Materials Run Cables to Base Station Locations Wire SpecificationsRun Cable for System Pull Cable Terminate Cable at Base Station LocationsPrepare Demarc Blocks MCUMultiple Power Pairs Dedicated Line for Diagnostic ModemTwo Wire Analog or Digital Interface Four Wire Digital Interface Install Demarc Blocks Assign and Program PortsSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Check Components Install Link Wireless Telephone SystemSurvey Site Connect MCU to Demarc Blocks Install MCUsMount MCUs to Wall Connect Power Connect Multi-Unit SystemsSet Switch Interface Type Switch Interface Line LEDs MCU Type Install Base Stations Mount Base Stations on Dropped Tile CeilingsMount Base Stations On Finished Ceilings Install Outdoor Base Stations Wire and Connect Outdoor Base StationsRegister Wireless Telephones Connect and Register Wireless TelephonesSet Up Diagnostic Modem Unregister Wireless Telephones Program Wireless Telephone Features Test Wireless TelephonesSite Certification Troubleshoot Phone Features System AdministrationTroubleshoot Error Codes Status LED Codes Status LEDs Description Action 12345Status Description Action LEDs Status Description Action LEDs Wireless Telephone Status Indicator Messages Indicator Description ActionRegister New Wireless Telephone Replace a Wireless TelephoneDelete Old Wireless Telephone Replace an MCU Clear Configuration on Replacement MCUConnect the Replacement MCU Replace a Base Station Wireless Telephone Planning Worksheet MCU IDBase Station Location Worksheet Appendix a Technical Parameters Select Alternate Spread Spectrum SequenceChange Companding Appendix B Program Analog Features Defining MacrosPlan Programming Open Application InterfaceProgram Macro Codes Examples of Programming TransferSpeed Dial Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway OAI Telephony Gateway’s Front Panel Mount Telephony Gateway to WallInitial Test Connect the OAI Telephony Gateway to the MCU Connect the OAI Telephony Gateway to the Application Server Assign a Function Key to OAI Telephony GatewayCertification Test Index LEDOAI