SpectraLink 150 M3 MCU manual Program Macro Codes

Page 54

SpectraLink Corporation

Link WTS Installation and Operation

12.3 Program Macro Codes

Functions are defined by placing an Administrative Call using the Administrative Wireless Telephone (registered to Line 2 of MCU 1). Follow these steps to place an administrative call and define functions.

! In multi- unit installations, be sure all MCUs are properly connected to one another before making an administrative call.

1.On the MCU that displays a box ID of 1, move the mode switch to the ADMIN position.

2.Press the START key on the administrative Wireless Telephone (the Wireless Telephone registered to MCU 1, line 2). This is the only Wireless Telephone enabled to make the administration call.

3.When you hear a steady tone (not a dial tone), the Wireless Telephone is in an administrative call and is ready to program.

4.Press the FCN key followed by the key strokes used to access the function. Valid keys are 0-9, *,#, START (flash), and FCN (pause). Note that FCN + 1 is reserved for Mute.

5.Press the function key sequence to be programmed. If a key sequence is incorrectly entered, go to the next step.

6.Press the END key to complete the programming of the function. Repeat steps 4- 7 for all remaining functions or to reprogram a function to correct an input error.

7.Return the mode switch to the NORM position.

The line LEDs now indicate line status and the administrative Wireless Telephone can now place calls normally.

Part Number: 72-0075-01-C-W.doc

Page 43

Image 54
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Questions? Installation OverviewAbout This Document Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation Link Wireless Telephone System Overview System OperationSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Site Preparation Required MaterialsDetermine Location of MCU Wire Specifications Run Cable for SystemRun Cables to Base Station Locations Pull Cable Terminate Cable at Base Station LocationsPrepare Demarc Blocks MCUMultiple Power Pairs Dedicated Line for Diagnostic ModemTwo Wire Analog or Digital Interface Four Wire Digital Interface Install Demarc Blocks Assign and Program PortsSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Install Link Wireless Telephone System Survey SiteCheck Components Install MCUs Mount MCUs to WallConnect MCU to Demarc Blocks Connect Power Connect Multi-Unit SystemsSet Switch Interface Type Switch Interface Line LEDs MCU Type Install Base Stations Mount Base Stations on Dropped Tile CeilingsMount Base Stations On Finished Ceilings Install Outdoor Base Stations Wire and Connect Outdoor Base StationsConnect and Register Wireless Telephones Set Up Diagnostic ModemRegister Wireless Telephones Unregister Wireless Telephones Program Wireless Telephone Features Test Wireless TelephonesSite Certification System Administration Troubleshoot Error CodesTroubleshoot Phone Features Status LED Codes Status LEDs Description Action 12345Status Description Action LEDs Status Description Action LEDs Wireless Telephone Status Indicator Messages Indicator Description ActionReplace a Wireless Telephone Delete Old Wireless TelephoneRegister New Wireless Telephone Clear Configuration on Replacement MCU Connect the Replacement MCUReplace an MCU Replace a Base Station Wireless Telephone Planning Worksheet MCU IDBase Station Location Worksheet Appendix a Technical Parameters Select Alternate Spread Spectrum SequenceChange Companding Plan Programming Appendix B Program Analog FeaturesDefining Macros Open Application InterfaceProgram Macro Codes Speed Dial Examples of ProgrammingTransfer Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway OAI Telephony Gateway’s Front Panel Mount Telephony Gateway to WallInitial Test Connect the OAI Telephony Gateway to the MCU Connect the OAI Telephony Gateway to the Application Server Assign a Function Key to OAI Telephony GatewayCertification Test Index LEDOAI