SpectraLink 150 M3 MCU manual Index, Led

Page 62

SpectraLink CorporationLink WTS Installation and Operation

 

Index

AC Adapter

Connecting MCU to Telephone System, 9

MCU, 18

Coverage, 4

OAI, 47

Customer Support Hotline, 1

A-law, 41

Demarcation blocks

Alternate sequence, 40

Four wire digital, 16

Function Keys, 49

Installing, 13

Attenuation, 7

Two wire analog or digital, 15

Base Station, 18

Diagnostic Modem, 10

Cabling, 7, 8

Error Codes, 30

Description, 4

ESD bonding strap, 18

Installation, 23

Extension numbers, 35

LED, 30

Features, Defining Macros for, 42

Location form, 39

Batteries, 19

Outdoor, 25

Forms

Outside Wiring, 25

Base Station location, 39

Replacing, 37

Wireless Telephone

Battery Chargers, 19

Planning Worksheet, 38

Cabling

Frequency, transmission, 40

Base Station specifications, 7

Hand-off, 4

Base Station, external, 13

Hotline, 1

Base Station, internal, 7

Interface types, Demarc, 9

Demarcation blocks, 13

Interference, frequency, 40

Exiting the building, 8

LED

Four wire digital, 12

Base Station, 30

IPC, 22, 45

Codes, 31

OAI Gateway, 45

Front Panel, 5

Prepare Demarc Blocks, 9

Line indicator, 5

Quick Clip Fuse, 6

Troubleshooting, 30

RJ-45 modular, 8

Link WTS, Overview, 3

RS-232, 45

Macros, Defining, 42

Shipped with system, 18

Master Control Unit. See MCU

Troubleshooting, 31

MCU

Two-wire analog or digital, 11

Base Station cabling, 8

Ceiling clip, 18, 23

Connect to Demarc Blocks, 19

Chargers, 19

Description, 3

Companding, 41

Front Panel, 5

Configuration sharing, 36

Location, 6

Part Number: 72-0075-01-C-W.doc

Page 51

Image 62
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Questions? Installation OverviewAbout This Document Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation Link Wireless Telephone System Overview System OperationSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Determine Location of MCU Site PreparationRequired Materials Run Cables to Base Station Locations Wire SpecificationsRun Cable for System Pull Cable Terminate Cable at Base Station LocationsPrepare Demarc Blocks MCUMultiple Power Pairs Dedicated Line for Diagnostic ModemTwo Wire Analog or Digital Interface Four Wire Digital Interface Install Demarc Blocks Assign and Program PortsSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Check Components Install Link Wireless Telephone SystemSurvey Site Connect MCU to Demarc Blocks Install MCUsMount MCUs to Wall Connect Power Connect Multi-Unit SystemsSet Switch Interface Type Switch Interface Line LEDs MCU Type Install Base Stations Mount Base Stations on Dropped Tile CeilingsMount Base Stations On Finished Ceilings Install Outdoor Base Stations Wire and Connect Outdoor Base StationsRegister Wireless Telephones Connect and Register Wireless TelephonesSet Up Diagnostic Modem Unregister Wireless Telephones Program Wireless Telephone Features Test Wireless TelephonesSite Certification Troubleshoot Phone Features System AdministrationTroubleshoot Error Codes Status LED Codes Status LEDs Description Action 12345Status Description Action LEDs Status Description Action LEDs Wireless Telephone Status Indicator Messages Indicator Description ActionRegister New Wireless Telephone Replace a Wireless TelephoneDelete Old Wireless Telephone Replace an MCU Clear Configuration on Replacement MCUConnect the Replacement MCU Replace a Base Station Wireless Telephone Planning Worksheet MCU IDBase Station Location Worksheet Appendix a Technical Parameters Select Alternate Spread Spectrum SequenceChange Companding Plan Programming Appendix B Program Analog FeaturesDefining Macros Open Application InterfaceProgram Macro Codes Speed Dial Examples of ProgrammingTransfer Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway OAI Telephony Gateway’s Front Panel Mount Telephony Gateway to WallInitial Test Connect the OAI Telephony Gateway to the MCU Connect the OAI Telephony Gateway to the Application Server Assign a Function Key to OAI Telephony GatewayCertification Test Index LEDOAI