SpectraLink 150 M3 MCU manual Industry Canada IC Notice

Page 6

SpectraLink Corporation

Link WTS Installation and Operation

Industry Canada (IC) Notice

Notice:

The Industry Canada (IC) label identifies certified equipment. This cert ification means that the equipment meets telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by a user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides as indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices.

REN 0.3B

Approval Numbers:

Link 150: 2128 -9760 A

Warranty and Repair Service Center:

SpectraLink Corporation 5755 Central Avenue Boulder, CO 80301 303-440-5330

DOC Spread Spectrum certification

Base Station

Cert. No.

2128-K1373

Wireless Telephone

Cert. No.

2128-K1374

Part Number: 72-0075-01-C-W.doc

Page vi

Image 6
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Questions? Installation OverviewAbout This Document Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation Link Wireless Telephone System Overview System OperationSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Site Preparation Required MaterialsDetermine Location of MCU Wire Specifications Run Cable for SystemRun Cables to Base Station Locations Pull Cable Terminate Cable at Base Station LocationsPrepare Demarc Blocks MCUMultiple Power Pairs Dedicated Line for Diagnostic ModemTwo Wire Analog or Digital Interface Four Wire Digital Interface Install Demarc Blocks Assign and Program PortsSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Install Link Wireless Telephone System Survey SiteCheck Components Install MCUs Mount MCUs to WallConnect MCU to Demarc Blocks Connect Power Connect Multi-Unit SystemsSet Switch Interface Type Switch Interface Line LEDs MCU Type Install Base Stations Mount Base Stations on Dropped Tile CeilingsMount Base Stations On Finished Ceilings Install Outdoor Base Stations Wire and Connect Outdoor Base StationsConnect and Register Wireless Telephones Set Up Diagnostic ModemRegister Wireless Telephones Unregister Wireless Telephones Program Wireless Telephone Features Test Wireless TelephonesSite Certification System Administration Troubleshoot Error CodesTroubleshoot Phone Features Status LED Codes Status LEDs Description Action 12345Status Description Action LEDs Status Description Action LEDs Wireless Telephone Status Indicator Messages Indicator Description ActionReplace a Wireless Telephone Delete Old Wireless TelephoneRegister New Wireless Telephone Clear Configuration on Replacement MCU Connect the Replacement MCUReplace an MCU Replace a Base Station Wireless Telephone Planning Worksheet MCU IDBase Station Location Worksheet Appendix a Technical Parameters Select Alternate Spread Spectrum SequenceChange Companding Plan Programming Appendix B Program Analog FeaturesDefining Macros Open Application InterfaceProgram Macro Codes Speed Dial Examples of ProgrammingTransfer Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway OAI Telephony Gateway’s Front Panel Mount Telephony Gateway to WallInitial Test Connect the OAI Telephony Gateway to the MCU Connect the OAI Telephony Gateway to the Application Server Assign a Function Key to OAI Telephony GatewayCertification Test Index LEDOAI