SpectraLink 150 M3 MCU manual Set Switch Interface Type

Page 32

SpectraLink Corporation

Link WTS Installation and Operation

Use only the provided Class II AC Adapter with output 24VDC, 1A.

!in power switch. This allows the MCUs to be turned on and off together.For installations with more than one MCU, use an outlet strip with a built

2.Plug the AC adapter into a 110VAC outlet or switch on the outlet strip to apply power to the MCU.

Set Switch Interface Type

The following steps explain how to assign a switch interface type to the MCU. This procedure must be done in on each MCU.

1.Power on the MCU with the Mode Switch in the NORMAL position.

Because the MCU does not have a switch type assigned, it will alarm (the Error LED will flash along with Status LEDs 1,2,3,4 and 5). This should take less than 2 minutes.

2.Power off the MCU.

3.Move the Mode Switch to ADMIN and power on the MCU. Within 15 seconds, Status LEDs 2 and 4 will light.

4.Press the STEP button three times.

Status LEDs 1, 2 and 4 must be lit. Line LEDs 1 through 8 (indicating an unconfigured MCU) should also be lit.

If any other combination of Line LEDs is lit, then a switch type has already been selected. Go to step 5 to pick the desired switch type.

5.Press the DEL/ENTER button to select the correct switch interface type. With each press of the DEL/ENTER button, a different series of Line LEDs will be lit. Continue to press DEL/ENTER until the correct Line LEDs are lit. Use the following list to select the desired switch interface.

Part Number: 72-0075-01-C-W.doc

Page 21

Image 32
Contents Installation and Operation Trademark Information SpectraLink Corporation Link WTS Installation and Operation UL Information FCC Information Industry Canada IC Notice Warranty Support Program Customer Responsibilities Return Material Authorization Cleaning Tips for Wireless Telephones Table of Contents Site Certification System Administration Installation Overview About This DocumentQuestions? Icons and ConventionsSpectraLink Corporation Link WTS Installation and Operation Link Wireless Telephone System Overview System OperationSpectraLink Corporation Link WTS Installation and Operation Front Panel of the Link 150 M3 MCU Determine Location of MCU Site PreparationRequired Materials Run Cables to Base Station Locations Wire SpecificationsRun Cable for System Pull Cable Terminate Cable at Base Station LocationsPrepare Demarc Blocks MCUMultiple Power Pairs Dedicated Line for Diagnostic ModemTwo Wire Analog or Digital Interface Four Wire Digital Interface Install Demarc Blocks Assign and Program PortsSpectraLink Corporation Link WTS Installation and Operation Two Wire Analog or Digital Demarc Block Four Wire Digital Demarc Block Wire Connector B Check Components Install Link Wireless Telephone SystemSurvey Site Connect MCU to Demarc Blocks Install MCUsMount MCUs to Wall Connect Power Connect Multi-Unit SystemsSet Switch Interface Type Switch Interface Line LEDs MCU Type Install Base Stations Mount Base Stations on Dropped Tile CeilingsMount Base Stations On Finished Ceilings Install Outdoor Base Stations Wire and Connect Outdoor Base StationsRegister Wireless Telephones Connect and Register Wireless TelephonesSet Up Diagnostic Modem Unregister Wireless Telephones Program Wireless Telephone Features Test Wireless TelephonesSite Certification Troubleshoot Phone Features System AdministrationTroubleshoot Error Codes Status LED Codes Status LEDs Description Action 12345Status Description Action LEDs Status Description Action LEDs Wireless Telephone Status Indicator Messages Indicator Description ActionRegister New Wireless Telephone Replace a Wireless TelephoneDelete Old Wireless Telephone Replace an MCU Clear Configuration on Replacement MCUConnect the Replacement MCU Replace a Base Station Wireless Telephone Planning Worksheet MCU IDBase Station Location Worksheet Appendix a Technical Parameters Select Alternate Spread Spectrum SequenceChange Companding Appendix B Program Analog Features Defining MacrosPlan Programming Open Application InterfaceProgram Macro Codes Examples of Programming TransferSpeed Dial Clear or Erase a FunctionBefore Installing the OAI Telephony Gateway OAI Telephony Gateway’s Front Panel Mount Telephony Gateway to WallInitial Test Connect the OAI Telephony Gateway to the MCU Connect the OAI Telephony Gateway to the Application Server Assign a Function Key to OAI Telephony GatewayCertification Test Index LEDOAI