VTech LS6245 Bluetooth system busy appears on the display, My telephone does not work at all

Page 86

Appendix

Troubleshooting

Bluetooth system busy appears on the display.

Make sure that your cell phone is not in use when connected and on the active devices list.

Make sure that your cell phone or headset is not connected to any other Bluetooth device.

LS6245 can only use one Bluetooth device at a time.

Unplug the telephone base power for 15 seconds, then plug it back in.

The PIN on the telephone base does not work.

The default PIN is 0000.

If you have changed the PIN, it appears on the telephone base in the pairing process.

I cannot hear any audio on my telephone system when on a cell call.

Reset the telephone base. Unplug the unit’s electrical power. Wait for approximately 15 seconds, then plug it back in.

Turn off your cell phone, then turn it on again.

My telephone does not work at all.

Make sure the battery is installed and charged correctly (page 4). For optimum daily performance, return the handset to the telephone base or charger after use.

Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.

Make sure the telephone line cord is plugged firmly into the telephone base and the telephone wall jack.

Unplug the electrical power to the telephone base. Wait for approximately 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to synchronize.

Charge the battery in the handset for up to 16 hours.

If the battery is completely depleted, it can take up to 10 minutes to charge the handset before HANDSET X appears on the screen (page 5).

Remove and re-insert the battery. If that still does not work, it might be necessary to purchase a new battery.

Disconnect the telephone base from the telephone wall jack and plug in a working telephone. If the other telephone does not work, the problem is probably in the wiring or the telephone service. Call your telephone service provider.

Low battery shows on screen.

Place the handset in the telephone base for recharging.

Remove and re-install the battery and use it until fully depleted, then recharge the handset in the telephone base for up to 16 hours.

If the above measures do not correct the problem, replace the battery.

82

Image 86
Contents User’s manual Congratulations Table of contents Index Answering system operation..67Appendix Parts checklist Getting startedImportant notes InstallationCleaning tips for your touch screen telephone Avoid placing the telephone base too close toTelephone base installation Battery installation Charge lightBattery charging Handset layout VOL+Telephone base layout HomeFLASH/X Handset main menu To enter the main menuTelephone base main menu Bluetooth Introducing BluetoothGlossary of terms Bluetooth at a glance Important InformationTo pair and connect a cell phone Bluetooth setupSetup cell Device connected to base, and 1 and/or 2 displaysSetup headset To pair and connect a headsetPaired devices Rename a paired deviceRemove a paired device View information of a paired deviceConnect/disconnect an active device Active devicesReview the active devices list To replace an active device Replace an active deviceAdd an active device To add an active deviceChange PIN Remove an active deviceView information of an active device LCD language Handset settingsSettings To select a languageTo manually turn off these indicators Clear voicemailKey tone To change the settingAuto keylock Set date/time Home area code 800Ringers Ringer volumeTo adjust the handset ringer volume Ringer tone To select a ringer toneTelephone base settings LCD Language Turn off indicator? 800 Ringer Volume Ringer tone Select Home Using the handset Answering system settingsAnswering system setup Answer ON/OFFCall screening To change the setting Using the telephone baseUsing a handset Announcement Play your announcementTone. Press 5 when you are done. After the tone Record your own announcementDelete your announcement Number of rings Remote access code Press the Menu softkey when the handset is not in useMessage alert tone Telephone operation Make, answer or end a home callUsing a Bluetooth headset Call waiting on the home lineMake, answer or end a cell call To answer the incoming cell call Call waiting on the cell lineAnswer a cell call while on a home call To end the cell callAnswer a home call while on a cell call Conference home and cell callsSilence the ringer Volume controlHandset speakerphone MuteHandset locator Infrared sensorHold Chain dialing To access a number in the call log while on a Home callTo access the last number redial while on a home call Dial a redial entry Redial listReview the redial list Save a redial entry to the directoryDelete a redial entry Intercom To end an intercom call Answer an incoming call during an intercom callTo silence an intercom call Share an outside call Transfer a callDirectory Create a new directory entryUsing the telephone base Character chart Alphabetical search To review the directory Using a handsetReview the directory To start an alphabetical searchEdit a directory entry To dial a directory entry Using a handsetDial a directory entry Press /HOME or /CELLDelete a directory entry To delete an entryAbout caller ID Information about caller ID with call waitingMissed calls indicator Caller ID historyMemory match Review the call logMake a call log entry ready to dial Dial a call log entrySave a call log entry to the directory Call log display screen messages To delete all entries Using a handsetDelete from the call log To delete a single entryMessage capacity Answering system operationAnswering system and voicemail New message indicationTo play messages with a handset Message playbackTo play messages with the telephone base Delete all old messages To record a memo Using the telephone base Record and play memosRemote access CommandAppendix Screen display messagesKeypad is locked Handset and telephone base indicators Handset lights Telephone base lightsBluetooth disconnected devices indicates that there Handset iconsBluetooth wireless headset on steadily when a Telephone base iconsBattery Operation Operating timeTo register a handset Expand your telephone systemAdd and register a handset optional Replace a handset To deregister all handsetsCannot pair my cell phone to the telephone base TroubleshootingCannot use the keypad Cannot pair my headset to the telephone baseCannot find VTech LS6245 on my cell phone Cannot put my headset in discoverable modeCannot connect my headset with the telephone base My cell phone disconnects with the telephone basePIN on the telephone base does not work Bluetooth system busy appears on the displayLow battery shows on screen My telephone does not work at allCharge light is off There is no dial toneTelephone does not ring when there is an incoming call Cannot dial outMy handset beeps and is not performing normally Hear noise on the cordless handset and the keys do not work Hear other calls when using the telephoneMy caller ID features are not working properly Registration failed appears on the handsetCannot retrieve my voicemail messages Caller ID entries do not match the numbers I need to dialSearching for Base shows in the handset screen Answering system does not record messages Outgoing announcement is not clearMessages on the answering system are very difficult to hear Common cure for electronic equipment Answering system does not respond to remote commandsMessages on the answering system are incomplete Important safety instructions Maintenance Operating rangeAbout cordless telephones Rbrc sealWarranty What does this limited warranty cover?Other limitations FCC, Acta and IC regulations FCC PartIndustry Canada Technical specifications Symbol IndexIndex 91-002418-030-100