VTech VT 9241 manual Base Unit Features, Power LED, Spare Batt LED, Charge LED

Page 11

BASE UNIT FEATURES

CONF KEY

*Press this key to establish a Conference call between LINE1 and LINE2.

REDIAL KEY

*Press this key to dial the last number called from the Base.

900MHZ
CORDLESS
VT9241
CONF	REDIAL	MUTE
HOLD	MEMORY	INT.COM/PAGE
		SPARE BATT
POWER	CHARGE
POWER
1	2ABC	3DEF
		VOL
4GHI	5JKL	6MNO
7PQRS	8TUV	9WXYZ
TONE	0OPER
	0OPER
FLASH		FLASH
LINE 1	OFF	LINE 2
	OFF
MIC

MUTE KEY/LED

*Press this key during an active call to disable the microphone. Press MUTE again to return to a 2-way conversation.

*While the SPEAKERPHONE is on, this LED will illuminate after pressing the MUTE key.

INT.COM/PAGE KEY/LED

*Press this key to page the Handset. The LED will flash while the Handset is paged, and it will glow steadily during Intercom mode.

MEMORY KEY

*Press this key to enter Memory mode.

POWER LED

*It illuminates when the base power adaptor is plugged in and power is applied to the base unit.

SPARE BATT LED

*The SPARE BATT LED lights up after a battery pack is placed in the spare battery compartment.

HOLD KEY

*Press this key to place a

Speakerphone call on hold .

*Press the appropriate LINE key to return to the call.

CHARGE LED

*The CHARGE LED illuminates

steadily to indicate that the H a n d s e t b a t t e r y i s b e i n g charged.

11

Image 11

Contents Introduction FeaturesWall Mounting Bracket Base Unit Battery pack Handset Belt clip AC adapterParts Check List Read and understand all instruc- tions Important Safety InstructionsRbrctm Seal If the product exhibits a distinct Change in performanceReplacing the Handset Battery To install the Spare Battery Pack Spare Battery ChargerCharge the Handset BATTER- IES Before USE. The batteries Getting StartedNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Charge LED Base Unit FeaturesPower LED Spare Batt LEDTONE/PULSE Switch OFF KEY Volume UP KEYVolume Down KEY Ringer SwitchesMaking Calls Operating InstructionsTo PUT a Call on Hold Mute FeatureTips on Usingthe VT 9241 Speak Erphone Answer a CallFrom the Base Unit Pressing the VOL UP or Down keysMaking or Answering a Call While YOU’RE Already on a Call Ference CallingJoining a Conversation Press Hold on the HandsetPress the appropriate Line key on the Base Unit Using the Intercom Programming the Ringer Type Using the Intercom During a Phone CallTemporary Tone Feature If Your Phone Rings During AN Intercom ConversationChecking the Ringer Turning OFF the RingersTo turn off the ringer on the Handset do the following Press PGM/MEMStoring a Pause in a Speed Dial Number To Store a Number Into MemoryTo Speed Dial a Stored Number To Change or Replace a Stored NumberConference Calling Using RedialStoring a Redial Number in Memory Speed Dial Ending One Side Or Entire Confer- ence Call Switching a Conference Call From Handset To Base UnitSwitching a Conference Call From Base Unit To Handset Way Conference CallingChanging Channels Installation Optional Headset Installation and Operating InstructionsONE Inch Data Port Electrical Storms MaintenanceExcess water or cleaning solvents of any kind Taking Care of Your TELE- PhoneNo Dial Tone Handset does not Ring When YOU Receive a CallCase of Difficulty Phone DOESN’T Work AT ALLYour Caller Fades in and OUT YOU Hear Other Calls While Using Your PhoneBase does not Ring Common Cure for Electronic EquipmentWarranty Statement HOW does State LAW Relate to this WARRANTY? What does OUR Warranty not COVER?FCC Part FCC and IC RegulationsUnited States Canada Vtech ElectronicsThis telephone is registered for use in Canada IC Industry CanadaOffice Receive Frequency Technical SpecificationsTransmit Frequency Weight Power RequirementsTable of Contents If Your Phone Rings During AN Intercom Conversation 91-5073-10-00 Issue