VTech VT 9241 manual OFF KEY Volume UP KEY, Volume Down KEY, Tone/* Key, LINE2 KEY, LINE1 KEY

Page 12

BASE UNIT FEATURES

900MHZ
CORDLESS
VT9241
CONF	REDIAL	MUTE
HOLD	MEMORY	INT.COM/PAGE
		SPARE BATT
POWER	CHARGE
POWER
1	2ABC	3DEF
		VOL
4GHI	5JKL	6MNO
7PQRS	8TUV	9WXYZ
TONE	0OPER
	0OPER
FLASH		FLASH
LINE 1	OFF	LINE 2
	OFF
MIC

OFF KEY

VOLUME UP KEY

*Press this key to adjust the speaker volume. There are total of 8 volume level settings.

VOLUME DOWN KEY

* Press this key to adjust the speaker volume. There are t o t a l o f 8 v o l u m e l e v e l settings.

TONE/* KEY

*In PULSE dialing mode, this key is used to switch to Temporary Tone.

LINE2 KEY

*Press this key to get dial tone or answer an incoming call on LINE2.

* P r e s s t h i s k e y t o F l a s h L I N E 2 w h i l e u s i n g t h e Speakerphone.

* Press this key to hang up a line or end an Intercom call .

LINE1 KEY

*Press this key to get dial tone or answer incoming call on LINE1 using the Speakerphone.

* Press this key to Flash operation in LINE1
while using the Speakerphone.		PORT
		DATA
	L2
RINGER SWITCHES	L1/L2	9V DCTEL.LINE

*	These switches will set the Base Ringer to		2	OFF	LOW
	HIGH, LOW or OFF.	RINGER	1LINE	OFF HIGH	LOW
			LINE		LOW

HIGH

TONE/PULSE SWITCH

DIAL MODE

PULSE TONE

*Located on the underside of the Base Unit, this switch sets your primary dialing mode. Most phone lines use Tone dialing.

12

Image 12

Contents Features IntroductionBase Unit Battery pack Handset Belt clip AC adapter Parts Check ListWall Mounting Bracket Important Safety Instructions Read and understand all instruc- tionsIf the product exhibits a distinct Change in performance Rbrctm SealReplacing the Handset Battery Spare Battery Charger To install the Spare Battery PackGetting Started Charge the Handset BATTER- IES Before USE. The batteriesNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Base Unit Features Power LEDSpare Batt LED Charge LEDOFF KEY Volume UP KEY Volume Down KEYRinger Switches TONE/PULSE SwitchOperating Instructions Making CallsMute Feature Tips on Usingthe VT 9241 Speak ErphoneAnswer a Call To PUT a Call on HoldPressing the VOL UP or Down keys Making or Answering a Call While YOU’RE Already on a CallFerence Calling From the Base UnitPress Hold on the Handset Press the appropriate Line key on the Base UnitJoining a Conversation Using the Intercom Using the Intercom During a Phone Call Temporary Tone FeatureIf Your Phone Rings During AN Intercom Conversation Programming the Ringer TypeTurning OFF the Ringers To turn off the ringer on the Handset do the followingPress PGM/MEM Checking the RingerTo Store a Number Into Memory To Speed Dial a Stored NumberTo Change or Replace a Stored Number Storing a Pause in a Speed Dial NumberUsing Redial Storing a Redial Number in Memory Speed DialConference Calling Switching a Conference Call From Handset To Base Unit Switching a Conference Call From Base Unit To HandsetWay Conference Calling Ending One Side Or Entire Confer- ence CallChanging Channels Optional Headset Installation and Operating Instructions InstallationONE Inch Data Port Maintenance Excess water or cleaning solvents of any kindTaking Care of Your TELE- Phone Electrical StormsHandset does not Ring When YOU Receive a Call Case of DifficultyPhone DOESN’T Work AT ALL No Dial ToneYOU Hear Other Calls While Using Your Phone Base does not RingCommon Cure for Electronic Equipment Your Caller Fades in and OUTWarranty Statement What does OUR Warranty not COVER? HOW does State LAW Relate to this WARRANTY?FCC and IC Regulations United StatesCanada Vtech Electronics FCC PartIC Industry Canada This telephone is registered for use in CanadaOffice Technical Specifications Transmit Frequency WeightPower Requirements Receive FrequencyTable of Contents If Your Phone Rings During AN Intercom Conversation Issue 91-5073-10-00