VTech VT 9241 manual Operating Instructions, Making Calls

Page 13

OPERATING INSTRUCTIONS

MAKING CALLS	1. Press OFF on the Handset;
From the Handset	OR,

1.Pick up the Handset and press LINE1 or LINE2.

INT.COM/PAGE		900MHz
		CORDLESS
LINE 1	OFF	LINE 2

FLASHFLASH

12ABC 3DEF

4GHI 5JKL 6MNO

2.When you hear a dial tone, dial the number. The LINE key you pressed on Handset will light up and the cor- responding LINE on Base Unit will double Flash.

If you make a mistake when dialing, press OFF to hang up, then press LINE1 or LINE2 to get dial tone again.

You must always press LINE1 or LINE2 before you can dial a call on the Hand- set.

Disconnecting

To end a call,

INT.COM/PAGE		900MHz
		CORDLESS
LINE 1	OFF	LINE 2

FLASHFLASH

12ABC 3DEF

4GHI 5JKL 6MNO

2.Place the Handset back in the Base Unit cradle.

From the Base

7PQRS 8TUV 9WXYZ

TONE	0OPER

FLASH	FLASH
LINE 1	LINE 2
	OFF

MIC

The Base Unit allows you to make and receive calls without using the Hand- set. You can use the Speakerphone on Base while the Handset is in or out of the Base.

1.Press the LINE1 or LINE2 on the Base Unit.

2.You will hear the dial tone over the speaker.

3.Adjust the volume controls on the face of the Base Unit if necessary.

4.Dial the number on the dial pad of the Base Unit.

5.When the party answers, speak to- ward the microphone.

13

Image 13

Contents Introduction FeaturesParts Check List Base Unit Battery pack Handset Belt clip AC adapterWall Mounting Bracket Read and understand all instruc- tions Important Safety InstructionsRbrctm Seal If the product exhibits a distinct Change in performanceReplacing the Handset Battery To install the Spare Battery Pack Spare Battery ChargerCharge the Handset BATTER- IES Before USE. The batteries Getting StartedNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Power LED Base Unit FeaturesSpare Batt LED Charge LEDVolume Down KEY OFF KEY Volume UP KEYRinger Switches TONE/PULSE SwitchMaking Calls Operating InstructionsTips on Usingthe VT 9241 Speak Erphone Mute FeatureAnswer a Call To PUT a Call on HoldMaking or Answering a Call While YOU’RE Already on a Call Pressing the VOL UP or Down keysFerence Calling From the Base UnitPress the appropriate Line key on the Base Unit Press Hold on the HandsetJoining a Conversation Using the Intercom Temporary Tone Feature Using the Intercom During a Phone CallIf Your Phone Rings During AN Intercom Conversation Programming the Ringer TypeTo turn off the ringer on the Handset do the following Turning OFF the RingersPress PGM/MEM Checking the RingerTo Speed Dial a Stored Number To Store a Number Into MemoryTo Change or Replace a Stored Number Storing a Pause in a Speed Dial NumberStoring a Redial Number in Memory Speed Dial Using RedialConference Calling Switching a Conference Call From Base Unit To Handset Switching a Conference Call From Handset To Base UnitWay Conference Calling Ending One Side Or Entire Confer- ence CallChanging Channels Installation Optional Headset Installation and Operating InstructionsONE Inch Data Port Excess water or cleaning solvents of any kind MaintenanceTaking Care of Your TELE- Phone Electrical StormsCase of Difficulty Handset does not Ring When YOU Receive a CallPhone DOESN’T Work AT ALL No Dial ToneBase does not Ring YOU Hear Other Calls While Using Your PhoneCommon Cure for Electronic Equipment Your Caller Fades in and OUTWarranty Statement HOW does State LAW Relate to this WARRANTY? What does OUR Warranty not COVER?United States FCC and IC RegulationsCanada Vtech Electronics FCC PartThis telephone is registered for use in Canada IC Industry CanadaOffice Transmit Frequency Weight Technical SpecificationsPower Requirements Receive FrequencyTable of Contents If Your Phone Rings During AN Intercom Conversation 91-5073-10-00 Issue