VTech VT 9241 manual Getting Started, Charge the Handset BATTER- IES Before USE. The batteries

Page 7

GETTING STARTED

Setting Up Your VT 9241

1.Choose an area near an electrical outlet and a telephone wall jack.

2.Plug the AC power adapter into an electrical outlet and the DC connec- tor to the back of the Base Unit.

NOTE: Connect power to the Base Unit before placing the Handset in the cradle.

3.Set the TONE/PULSE switch located on the underside of the Base Unit. If you have touch tone service on your phone line, set the switch to TONE. If you have rotary service, set the switch to PULSE.

DIAL MODE
PULSE	TONE

4.Set the RINGER switches to HIGH, LOW or OFF on the Base Unit.

5.CHARGE THE HANDSET BATTER- IES BEFORE USE. The batteries

recharge automatically whenever the Handset is in the Base Unit cradle. The batteries must be charged for 16 hours before using your phone for the first time.

6.Connect the telephone line cord(s). If you have two lines which are ser- viced by one telephone jack (RJ14), insert one end of the four wire (black tipped) telephone line cord into the jack marked L1/L2 at the rear of the Base Unit. Plug the other end into a telephone wall jack. If your two tele- phone lines are each serviced by a separate telephone jack (RJ11), insert one end of a telephone line cord into the jack marked L1/L2 (this will be your line 1) and a second telephone cord into the jack marked L2 (this will be your Line2) at the rear of the Base Unit. Plug the other end of the telephone cords into the appropriate wall jacks. Make sure the plugs snap securely into place.

7.CHECK FOR A DIAL TONE. After the batteries are charged, pick up the Handset and press a LINE key. The LINE key you pressed should light up, and you should hear a dial tone. If not, see IN CASE OF DIFFI-

CULTY.

AC ELECTRICAL OUTLET

TELEPHONE

WALL JACK

LINE 1	RINGER	LINE 2
HIGH	OFF HIGH	OFF		L1/L2	L2
LOW		LOW	9V DC	TEL.LINE	DATA PORT

BASE UNIT RINGER	OR
SWITCHES

CAUTION: Use only the AC adapter shipped with your VT 9241. This is a Class 2 AC adapter, specifi- cally designed for use with the VT 9241.

7

Image 7

Contents Introduction FeaturesParts Check List Base Unit Battery pack Handset Belt clip AC adapterWall Mounting Bracket Read and understand all instruc- tions Important Safety Instructions Rbrctm Seal If the product exhibits a distinct Change in performanceReplacing the Handset Battery To install the Spare Battery Pack Spare Battery ChargerCharge the Handset BATTER- IES Before USE. The batteries Getting StartedNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Charge LED Base Unit FeaturesPower LED Spare Batt LEDTONE/PULSE Switch OFF KEY Volume UP KEYVolume Down KEY Ringer SwitchesMaking Calls Operating InstructionsTo PUT a Call on Hold Mute FeatureTips on Usingthe VT 9241 Speak Erphone Answer a CallFrom the Base Unit Pressing the VOL UP or Down keysMaking or Answering a Call While YOU’RE Already on a Call Ference CallingPress the appropriate Line key on the Base Unit Press Hold on the HandsetJoining a Conversation Using the Intercom Programming the Ringer Type Using the Intercom During a Phone CallTemporary Tone Feature If Your Phone Rings During AN Intercom ConversationChecking the Ringer Turning OFF the RingersTo turn off the ringer on the Handset do the following Press PGM/MEMStoring a Pause in a Speed Dial Number To Store a Number Into MemoryTo Speed Dial a Stored Number To Change or Replace a Stored NumberStoring a Redial Number in Memory Speed Dial Using RedialConference Calling Ending One Side Or Entire Confer- ence Call Switching a Conference Call From Handset To Base UnitSwitching a Conference Call From Base Unit To Handset Way Conference CallingChanging Channels Installation Optional Headset Installation and Operating InstructionsONE Inch Data Port Electrical Storms MaintenanceExcess water or cleaning solvents of any kind Taking Care of Your TELE- PhoneNo Dial Tone Handset does not Ring When YOU Receive a CallCase of Difficulty Phone DOESN’T Work AT ALLYour Caller Fades in and OUT YOU Hear Other Calls While Using Your PhoneBase does not Ring Common Cure for Electronic EquipmentWarranty Statement HOW does State LAW Relate to this WARRANTY? What does OUR Warranty not COVER?FCC Part FCC and IC RegulationsUnited States Canada Vtech ElectronicsThis telephone is registered for use in Canada IC Industry CanadaOffice Receive Frequency Technical SpecificationsTransmit Frequency Weight Power RequirementsTable of Contents If Your Phone Rings During AN Intercom Conversation 91-5073-10-00 Issue