VTech VT 9241 manual Technical Specifications, Transmit Frequency Weight, Power Requirements, Size

Page 35

TECHNICAL SPECIFICATIONS

FREQUENCY CONTROL

•Crystal Controlled Dual PLL Synthe sizer

TRANSMIT FREQUENCY

WEIGHT

•Handset: 180 grams

•Base: 500 grams

POWER REQUIREMENTS

•Handset: 923.10 MHz to 927.75 MHz (All thirty channels within this range)

•Base: 902.3 MHz to 906.65 MHz (All thirty channels within this range)

RECEIVE FREQUENCY

•Handset: Self-contained nickel- cadmium rechargeable battery supply, 3.6V nominal, 400mAh ca- pacity.

•Power Adapter: 9V DC@500mA

•Handset: 902.3 MHz to 906.65 MHz (All thirty channels within this range)

•Base: 923.10 MHz to 927.75 MHz (All thirty channels within this range)

SPECIFICATIONS ARE TYPI- CAL AND MAY CHANGE WITH- OUT NOTICE.

NOMINAL EFFECTIVE RANGE

•Maximum power allowed by FCC. Actual operating range may vary according to environmental condi- tions at the time of use.

•The range quoted for this phone is Based on open field measurements under ideal conditions.

SIZE

•Handset: 17.3cm x 5.6cm x 3.8cm (L x W x T) maximum (antenna excluded)

•Base: 21.9cm x 16.4cm x 5.4cm (L x W x T) maximum (antenna excluded)

35

Image 35

Contents Introduction FeaturesWall Mounting Bracket Base Unit Battery pack Handset Belt clip AC adapterParts Check List Read and understand all instruc- tions Important Safety InstructionsRbrctm Seal If the product exhibits a distinct Change in performanceReplacing the Handset Battery To install the Spare Battery Pack Spare Battery ChargerCharge the Handset BATTER- IES Before USE. The batteries Getting StartedNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Charge LED Base Unit FeaturesPower LED Spare Batt LEDTONE/PULSE Switch OFF KEY Volume UP KEYVolume Down KEY Ringer SwitchesMaking Calls Operating InstructionsTo PUT a Call on Hold Mute FeatureTips on Usingthe VT 9241 Speak Erphone Answer a CallFrom the Base Unit Pressing the VOL UP or Down keysMaking or Answering a Call While YOU’RE Already on a Call Ference CallingJoining a Conversation Press Hold on the HandsetPress the appropriate Line key on the Base Unit Using the Intercom Programming the Ringer Type Using the Intercom During a Phone CallTemporary Tone Feature If Your Phone Rings During AN Intercom ConversationChecking the Ringer Turning OFF the RingersTo turn off the ringer on the Handset do the following Press PGM/MEMStoring a Pause in a Speed Dial Number To Store a Number Into MemoryTo Speed Dial a Stored Number To Change or Replace a Stored NumberConference Calling Using RedialStoring a Redial Number in Memory Speed Dial Ending One Side Or Entire Confer- ence Call Switching a Conference Call From Handset To Base UnitSwitching a Conference Call From Base Unit To Handset Way Conference CallingChanging Channels Installation Optional Headset Installation and Operating InstructionsONE Inch Data Port Electrical Storms MaintenanceExcess water or cleaning solvents of any kind Taking Care of Your TELE- PhoneNo Dial Tone Handset does not Ring When YOU Receive a CallCase of Difficulty Phone DOESN’T Work AT ALLYour Caller Fades in and OUT YOU Hear Other Calls While Using Your PhoneBase does not Ring Common Cure for Electronic EquipmentWarranty Statement HOW does State LAW Relate to this WARRANTY? What does OUR Warranty not COVER?FCC Part FCC and IC RegulationsUnited States Canada Vtech ElectronicsThis telephone is registered for use in Canada IC Industry CanadaOffice Receive Frequency Technical SpecificationsTransmit Frequency Weight Power RequirementsTable of Contents If Your Phone Rings During AN Intercom Conversation 91-5073-10-00 Issue