VTech VT 9241 manual Switching a Conference Call From Handset To Base Unit, Way Conference Calling

Page 22

OPERATING INSTRUCTIONS

TONE 0OPER

HOLD CHAN INT.COM

PGM CONF REDIAL

MEM

PAUSE

2.Your original call will automatically be placed on HOLD.

3.Press CONF to join both lines to- gether. Both LINE keys will glow dur- ing a Conference call.

Switching A Conference Call From Handset To Base Unit

Once you have established a Confer- ence call on Handset,

1.Press HOLD on the Handset.

2.Press CONF on the Base Unit.

900MHZ

CORDLESS

VT9241

CONF REDIAL MUTE

HOLD MEMORY INT.COM/PAGE

SPARE BATT

CHARGE

POWER

3.Your Conference call has now been transferred to the Speakerphone.

Switching A Conference Call From Base Unit To Handset

Once you have established a Confer- ence Call on the Base,

1. Press HOLD on the Base

2.Press CONF key on the Handset.

3.Your conference call has now been transferred to the Handset.

4-Way Conference Calling

Both the Handset and Base Unit can participate in a Conference call at the same time. Once the Conference call has been established on the Handset (or Base):

1.Press LINE1 on the Base Unit (or Handset)

2.Press LINE2 on the Base Unit (or Handset)

3.Press CONF on the Base Unit (or Handset)

900MHZ
CORDLESS
VT9241
CONF	REDIAL	MUTE
HOLD	MEMORY	INT.COM/PAGE
		SPARE BATT
POWER	CHARGE
POWER

4.The Base Unit or Handset can exit the Conference call by pressing OFF.

Ending One Side Or Entire Confer- ence Call

If you want to end the call with only one person,

1.Press the LINE key of the person you want to disconnect

2.Press OFF

22

Image 22

Contents Features IntroductionParts Check List Base Unit Battery pack Handset Belt clip AC adapterWall Mounting Bracket Important Safety Instructions Read and understand all instruc- tionsIf the product exhibits a distinct Change in performance Rbrctm SealReplacing the Handset Battery Spare Battery Charger To install the Spare Battery PackGetting Started Charge the Handset BATTER- IES Before USE. The batteriesNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Spare Batt LED Base Unit FeaturesPower LED Charge LEDRinger Switches OFF KEY Volume UP KEYVolume Down KEY TONE/PULSE SwitchOperating Instructions Making CallsAnswer a Call Mute FeatureTips on Usingthe VT 9241 Speak Erphone To PUT a Call on HoldFerence Calling Pressing the VOL UP or Down keysMaking or Answering a Call While YOU’RE Already on a Call From the Base UnitPress the appropriate Line key on the Base Unit Press Hold on the HandsetJoining a Conversation Using the Intercom If Your Phone Rings During AN Intercom Conversation Using the Intercom During a Phone CallTemporary Tone Feature Programming the Ringer TypePress PGM/MEM Turning OFF the RingersTo turn off the ringer on the Handset do the following Checking the RingerTo Change or Replace a Stored Number To Store a Number Into MemoryTo Speed Dial a Stored Number Storing a Pause in a Speed Dial NumberStoring a Redial Number in Memory Speed Dial Using RedialConference Calling Way Conference Calling Switching a Conference Call From Handset To Base UnitSwitching a Conference Call From Base Unit To Handset Ending One Side Or Entire Confer- ence CallChanging Channels Optional Headset Installation and Operating Instructions InstallationONE Inch Data Port Taking Care of Your TELE- Phone MaintenanceExcess water or cleaning solvents of any kind Electrical StormsPhone DOESN’T Work AT ALL Handset does not Ring When YOU Receive a CallCase of Difficulty No Dial ToneCommon Cure for Electronic Equipment YOU Hear Other Calls While Using Your PhoneBase does not Ring Your Caller Fades in and OUTWarranty Statement What does OUR Warranty not COVER? HOW does State LAW Relate to this WARRANTY?Canada Vtech Electronics FCC and IC RegulationsUnited States FCC PartIC Industry Canada This telephone is registered for use in CanadaOffice Power Requirements Technical SpecificationsTransmit Frequency Weight Receive FrequencyTable of Contents If Your Phone Rings During AN Intercom Conversation Issue 91-5073-10-00