VTech VT 9241 manual If Your Phone Rings During AN Intercom Conversation, Temporary Tone Feature

Page 18

OPERATING INSTRUCTIONS

To return to the phone call, press the appropriate LINE key on Base or Hand- set.

IF YOUR PHONE RINGS DURING AN INTERCOM CONVERSATION

If you receive a call while using the In- tercom, the Base will only ring once, and the Handset will generate 3 alert- ing tones through the earpiece. The LINE key will flash on both Base and Handset. You can answer the incom- ing call by pressing the LINE key of the ringing line on the Base or Handset. However, by answering the incoming call you will automatically exit the In- tercom mode.

USING THE INTERCOM DURING A PHONE CALL

The HOLD feature allows you to put a phone call on hold and use the Inter- com without disconnecting your caller. It works at the Handset or the Base.

1.While you are on the call on the Handset, press the INT.COM key to automatically place the active call on hold, and to establish an Inter- com call between the Handset and Base.

TONE 0OPER

HOLD CHAN INT.COM

PGM CONF REDIAL

MEM

PAUSE

2.While you are on the call on the Base Unit, press HOLD and then

press INT.COM/PAGE on the Base to page the Handset. Then press INT.COM on the Handset to enter Intercom mode.

3.To end the Intercom conversation, press OFF on either the Handset or OFF on the Base Unit.

4.To return to the call, press the ap- propriate LINE key on the Handset or Base.

TEMPORARY TONE FEATURE

If you have rotary (dial-pulse) tele- phone service, (TONE/PULSE switch is set to PULSE), this feature allows you to enter special codes and tones to operate answering machines, use elec- tronic banking services, calling cards, or other special services.

To do this:

1.Dial the call normally.

2.Activate the temporary tone feature by pressing TONE (the *key).

3.Press the numbers or symbols you need, and your phone will send the proper signals.

This feature is available on both the Handset and the Base Unit.

To end the call, press OFF . The phone will automatically go back to rotary (dial-pulse) service.

PROGRAMMING THE RINGER TYPE

The VT 9241 features four different Handset ringer types for each line.

18

Image 18
Contents Features IntroductionBase Unit Battery pack Handset Belt clip AC adapter Parts Check ListWall Mounting Bracket Important Safety Instructions Read and understand all instruc- tionsIf the product exhibits a distinct Change in performance Rbrctm SealReplacing the Handset Battery Spare Battery Charger To install the Spare Battery PackGetting Started Charge the Handset BATTER- IES Before USE. The batteriesNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Spare Batt LED Base Unit FeaturesPower LED Charge LEDRinger Switches OFF KEY Volume UP KEYVolume Down KEY TONE/PULSE SwitchOperating Instructions Making CallsAnswer a Call Mute FeatureTips on Usingthe VT 9241 Speak Erphone To PUT a Call on HoldFerence Calling Pressing the VOL UP or Down keysMaking or Answering a Call While YOU’RE Already on a Call From the Base UnitPress Hold on the Handset Press the appropriate Line key on the Base UnitJoining a Conversation Using the Intercom If Your Phone Rings During AN Intercom Conversation Using the Intercom During a Phone CallTemporary Tone Feature Programming the Ringer TypePress PGM/MEM Turning OFF the RingersTo turn off the ringer on the Handset do the following Checking the RingerTo Change or Replace a Stored Number To Store a Number Into MemoryTo Speed Dial a Stored Number Storing a Pause in a Speed Dial NumberUsing Redial Storing a Redial Number in Memory Speed DialConference Calling Way Conference Calling Switching a Conference Call From Handset To Base UnitSwitching a Conference Call From Base Unit To Handset Ending One Side Or Entire Confer- ence CallChanging Channels Optional Headset Installation and Operating Instructions InstallationONE Inch Data Port Taking Care of Your TELE- Phone MaintenanceExcess water or cleaning solvents of any kind Electrical StormsPhone DOESN’T Work AT ALL Handset does not Ring When YOU Receive a CallCase of Difficulty No Dial ToneCommon Cure for Electronic Equipment YOU Hear Other Calls While Using Your PhoneBase does not Ring Your Caller Fades in and OUTWarranty Statement What does OUR Warranty not COVER? HOW does State LAW Relate to this WARRANTY?Canada Vtech Electronics FCC and IC RegulationsUnited States FCC PartIC Industry Canada This telephone is registered for use in CanadaOffice Power Requirements Technical SpecificationsTransmit Frequency Weight Receive FrequencyTable of Contents If Your Phone Rings During AN Intercom Conversation Issue 91-5073-10-00