VTech VT 9241 manual Important Safety Instructions, Read and understand all instruc- tions

Page 3

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, in- cluding the following:

1.Read and understand all instruc- tions.

2.Follow all warnings and instructions marked on the product.

3.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4.Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool).

5.Do not place this product on an un- stable cart, stand, or table. The prod- uct may fall, causing serious dam- age to the product.

6.Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from over- heating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installa- tion where proper ventilation is not provided.

7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8.Do not allow anything to rest on the power cord. Do not locate this prod- uct where the cord will be abused by persons walking on it.

9.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10.To reduce the risk of electric shock, do not disassemble this product. If service or repair work is required, contact VTech Customer Service at 1-800-595-9511. Opening or re- moving cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the ap- pliance is subsequently used.

11.Do not overload wall outlets and ex- tension cords as this can result in the risk of fire or electric shock.

12.Unplug this product from the wall outlet :

A.When the power supply cord or plug is damaged or frayed.

B.If liquid has been spilled into the product.

C.If the product has been exposed to rain or water.

D.If the product does not operate nor- mally by following the operating in- structions. Adjust only those con- trols that are covered by the oper-

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Introduction FeaturesBase Unit Battery pack Handset Belt clip AC adapter Parts Check ListWall Mounting Bracket Read and understand all instruc- tions Important Safety InstructionsRbrctm Seal If the product exhibits a distinct Change in performanceReplacing the Handset Battery To install the Spare Battery Pack Spare Battery ChargerCharge the Handset BATTER- IES Before USE. The batteries Getting StartedNever install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Charge LED Base Unit FeaturesPower LED Spare Batt LEDTONE/PULSE Switch OFF KEY Volume UP KEYVolume Down KEY Ringer SwitchesMaking Calls Operating InstructionsTo PUT a Call on Hold Mute FeatureTips on Usingthe VT 9241 Speak Erphone Answer a CallFrom the Base Unit Pressing the VOL UP or Down keysMaking or Answering a Call While YOU’RE Already on a Call Ference CallingPress Hold on the Handset Press the appropriate Line key on the Base UnitJoining a Conversation Using the Intercom Programming the Ringer Type Using the Intercom During a Phone CallTemporary Tone Feature If Your Phone Rings During AN Intercom ConversationChecking the Ringer Turning OFF the RingersTo turn off the ringer on the Handset do the following Press PGM/MEMStoring a Pause in a Speed Dial Number To Store a Number Into MemoryTo Speed Dial a Stored Number To Change or Replace a Stored NumberUsing Redial Storing a Redial Number in Memory Speed DialConference Calling Ending One Side Or Entire Confer- ence Call Switching a Conference Call From Handset To Base UnitSwitching a Conference Call From Base Unit To Handset Way Conference CallingChanging Channels Installation Optional Headset Installation and Operating InstructionsONE Inch Data Port Electrical Storms MaintenanceExcess water or cleaning solvents of any kind Taking Care of Your TELE- PhoneNo Dial Tone Handset does not Ring When YOU Receive a CallCase of Difficulty Phone DOESN’T Work AT ALLYour Caller Fades in and OUT YOU Hear Other Calls While Using Your PhoneBase does not Ring Common Cure for Electronic EquipmentWarranty Statement HOW does State LAW Relate to this WARRANTY? What does OUR Warranty not COVER?FCC Part FCC and IC RegulationsUnited States Canada Vtech ElectronicsThis telephone is registered for use in Canada IC Industry CanadaOffice Receive Frequency Technical SpecificationsTransmit Frequency Weight Power RequirementsTable of Contents If Your Phone Rings During AN Intercom Conversation 91-5073-10-00 Issue
Top Page Image Contents