Avaya 4601, 4602SW, 4612, 4620SW, 4606, 4610SW manual Dhcp s secs # to program Vlan ID = n

Page 28

4600 Series IP Telephone Installation

2. The IP telephone sends a request to the DHCP server and invokes the DHCP process.

One of the following messages display:

DHCP: s secs

 

DHCP: s secs

# to program

 

VLAN ID = n

 

 

 

DHCP: s secs

where s is the number of seconds that have elapsed since DHCP was invoked. The message on the left appears if 802.1Q tagging is off and access to local programming procedures is not disabled or restricted. (See Chapter 3: Local Administrative Options for specifics.) The middle message appears if 802.1Q tagging is on and access to local programming procedures is disabled or restricted. If the left and middle messages alternate every two seconds, 802.1Q tagging is on. When both messages alternate, access to local programming procedures is not disabled or restricted. Finally, the message on the right appears if 802.1Q tagging is off and access to local programming procedures is disabled or restricted.

3.The DHCP server provides IP addresses for the following hardware:

●The IP telephone

●The TFTP or HTTP server

●The TN799B, C, or D Control-LAN (CLAN) circuit pack on the media server

The 4601 cannot display messages. Therefore, if the DHCP process locates the required information, the 4601’s Call Appearance Line b indicator flashes continuously 500 milliseconds on, 500 milliseconds off while all other LEDs remain lit. If the appropriate information cannot be discerned or is missing, the 4601’s Call Appearance Line a indicator flutters 50 milliseconds on, 50 milliseconds off three times while all other LEDs remain lit, and a reset occurs.

4.Using the list of gateway IP addresses provided by the DHCP server, the phone performs a router check. The phone cycles through the gateway IP addresses with ARPs or pings until it receives a response. During this search, the 4601’s Call Appearance Line b indicator flashes continuously 500 milliseconds on, 500 milliseconds off. All other 4601 LEDs remain lit.

When the router is located, the TFTP or HTTP process starts. If no router is found for a 4601 IP Telephone, its Call Appearance Line b flutters 50 milliseconds on, 50 milliseconds off three times. All other 4601 LEDs remain lit, and a reset occurs.

28 4600 Series IP Telephone Release 2.2 Installation Guide

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Series IP Telephone Copyright 2005, Avaya Inc All Rights Reserved Introduction Index About This Guide Intended AudienceInstallation Guide Document OrganizationTerms Used in This Guide Command AdministrativeOnline Documentation DeviceRelated Documents Avaya Communication Manager Software Documentation ReleaseIP Telephone User Guide Customer Support 4601/4602/4602SW IP Telephone Stand InstructionsPage Series IP Telephone Installation IntroductionIP Telephone Models Requirements to Verify about the Network Pre-Installation ChecklistMedia Server Avaya IP IP Telephone Release 16 4600 Series IP Telephone Release 2.2 Installation Guide Requirements to Verify for Each IP Telephone Optional Items for Some IP TelephonesPowering the 4600 IP Telephone Assembling the 4600 Series IP TelephoneTelephone Model See 4621SW 4622SW 4625SW 4630/4630SW 4610SW 469020 4600 Series IP Telephone Release 2.2 Installation Guide Assembling the 4600 Series IP Telephone 22 4600 Series IP Telephone Release 2.2 Installation Guide Assembling the 4600 Series IP Telephone Connection Jacks on a 4630/4630SW IP Telephone Connection Jacks on a 4610SW IP Telephone Connection Jacks on a 4690 IP Conference Telephone Dynamic Addressing Process Dhcp s secs # to program Vlan ID = n 46xxUPGRADE.SCR n KB received Http n uriFilename KB received Saving to flash 1%, 1 secsPassword= #=OK Extension=nnnnnn #=OK NEW=Downgrading Avaya IP Telephones Page Local Administrative Options Entering Data for Administrative Options IP Telephone # Backspace Alternative Speaker buttonConference button Headset buttonEntering Data for the 4601 IP Telephone ThenAbout Local Administrative Procedures Local Programming Option Code SeeGroup Identifier on Pre-Installation Checklist for Static Addressing Static Addressing InstallationPhone=nnn.nnn.nnn.nnn Nnn.nnn.nnn.nnn Phone=CallSv=nnn.nnn.nnn.nnn Nnn.nnn.nnn.nnn CallSv=Router=nnn.nnn.nnn.nnn Nnn.nnn.nnn.nnn Router=Mask=nnn.nnn.nnn.nnn Nnn.nnn.nnn.nnn Mask=Vlan ID=dddd New= Vlan test=ddd New=Save new values? *=no #=yes New values being savedQoS Option Setting L2 signaling=d New=Mute 7 6 7 # Mute Q O S # L2 audio=d New=No new values. #=OK L3 signaling=dd New=Save new values? =no #=yes Mute 4 6 8 # Mute I N T # Interface ControlPHY1=status *=change #=OK Save new value? =no #=yes PHY2=status *=change #=OKIR=enabled 0=disable #=OK IR=disabled 1=enable #=OK New value being savedMute 4 7 6 8 7 Mute G R O U P Group IdentifierGroup=ddd New= Computer-Telephony Integration CTI Enable/Disable CTI=manual 0=Off #=OK CTI=disabled 1=Manual #=OKMute 2 8 4 # Mute C T I # UDP Port=497xx New=Mute 7 7 6 6 # Mute S S O N # Site-Specific Option Number SettingSSON=ddd New= Reset System Values Mute 7 3 7 3 8 # Mute R E S E T #Reset values? *=no #=yes Resetting valuesAre you sure? *=no #=yes Restart phone? =no #=yesRestart the Telephone Mute 7 4 4 Mute S I G Signaling Protocol IdentifierSIG=protocol *=change #=OK Signaling Protocol Identifier Self-Test Procedure Mute 8 3 7 8 # Mute T E S T #Self test #=end Self test passed #=endClear Procedure Mute 2 5 3 2 7 # Mute C L E a R #Clear all values? =no #=yes Are you sure? =no #=yesVisual/Audible Alerting Procedure Alerting=setting *=change #=OKClearing values Mute 2 5 3 7 8 # Mute a L E R T #Manually Setting the Dhcp Client Hardware Address Mute 2 4 2 3 3 7 # Mute C H a D D R #Chaddr=ddd New= All phones save the new valueSetting L2Q Tagging Control 4601 Only Mute 8 2 4 # Mute T a G #Page Troubleshooting Guidelines Error ConditionsDtmf Tones View Administrative Option Ccccccccc 00601DhhhhhhCccc Nnn.nnn.nnn.nnnError and Status Messages Aaa.bbb.ccc.dddSoftphone Explained in Local Administrative Options Undefined Error Resource Error Troubleshooting the 4601 IP Telephone Line a, which is flashing Cause The PBX does not recognize the set type Page Reset values? =no #=yes Scenarios for the Restart ProcessRestarting Loading 5 secs Replbootv3.app 4084KBInitializing Dhcp 0 secs * to program Starting Updating boot codeTftp n Http n uri Appfilename n KB received Saving to flash n%, x secsLoading 5 secs App 4035 KB StartingSecs ClearingUpdating Where n is the number of KBs downloaded Appfilename n KB received 82 4600 Series IP Telephone Release 2.2 Installation Guide Scenarios for the Restart Process Page Index 86 4600 Series IP Telephone Release 2.2 Installation Guide
Related manuals
Manual 18 pages 16.65 Kb Manual 1 pages 15.59 Kb Manual 90 pages 7.31 Kb Manual 66 pages 59.25 Kb Manual 6 pages 35.08 Kb Manual 60 pages 13.34 Kb

4602, 4602SW, 4620SW, 4601, 4612 specifications

The Avaya 4606 is a versatile and robust IP desk phone designed primarily for business environments that require reliable communication solutions. Part of Avaya's 4600 series, this model integrates advanced technology with user-friendly functionality, accommodating the needs of both everyday users and IT managers.

One of the standout features of the Avaya 4606 is its large graphical display, which provides clear visibility and easy access to essential information. The phone is equipped with a four-line display that allows users to navigate through various menus, check call logs, and access voicemail with ease. Additionally, the display supports multiple languages, catering to a global workforce.

The Avaya 4606 offers a comprehensive range of calling features designed to enhance productivity. These include standard capabilities such as call waiting, call transfer, and speed dialing, as well as more advanced functions like conference calling and directory browsing. The device supports multiple lines, making it simple for users to manage several calls simultaneously.

From a technology standpoint, the Avaya 4606 is built on the Session Initiation Protocol (SIP), enabling seamless integration with various communication platforms. This technology ensures high-quality voice communication while allowing for easy customization and scalability in response to changing business needs. The phone is also compatible with Avaya’s One-X portal, providing users with additional features like unified messaging and mobile integration.

The Avaya 4606 is designed with user comfort in mind. It features ergonomic handset design and adjustable tilting options, allowing users to position the phone for optimal viewing and comfort during long calls. The dedicated buttons for frequently used functions further streamline operations and reduce the learning curve for new users.

Security is a critical aspect of any business communication tool, and the Avaya 4606 addresses this with built-in encryption capabilities that safeguard sensitive communications. This is particularly important in industries where confidentiality is paramount.

With its combination of user-friendly features, advanced technology, and security, the Avaya 4606 is well-suited for enterprises looking to enhance their communication infrastructure. Whether for individual users or office teams, this desk phone delivers reliable performance that can adapt and evolve with business needs. Its straightforward setup and management also appeal to IT departments, making it a comprehensive solution for modern workplaces.
Top Page Image Contents