Nortel Networks i2022 Series manual Example, AUTO-Install

Page 15

i2022 ISDN Teleset

Example:

Press the softkey under Directory - shown below by highlighting (bold type) the word “DIR” and highlighting the softkey below that menu item.

Pressing the Directory softkey brings up the second menu with additional choices. In our example we chose Search next - shown in bold type. The selected menu items are shown in bold type for emphasis. The softkey under Search is highlighted to indicate the chosen softkey.

Choosing Search returns the next screen, assuming the Directory is empty.

Setup

To return to the main menu at any time, press the MENU hardkey.

CONNECTING THE i2022- AUTO-INSTALL

1. Assemble the i2022

NOTE: Make sure the logo plate is installed

2.Verify the PS1/PS2 switch located on the Interface Module is in the PS2 position. See page 6 for further information on setting the PS1/PS2 switch.

3.Verify the Terminating Resistor (TR) switch is set correctly. See page 8 for further information on setting the TR switch.

4.Connect one end of the eight-pin mounting cord to the ISDN Line-In jack on the rear of the Teleset’s Interface Module. Connect the other end of the cord to the S/T jack on your NT1 or ISDN telephone wall jack.

5.Remove the protective film on the display.

6.Label and install the designation card

AUTO-Install

The i2022 is equipped with an Auto-Install feature. The purpose of Auto-INSTALL is to ensure a complete and painless installation. In this mode, the i2022 will first detect the type of switch the i2022 is connected to, and then will attempt to Auto-SPID. The switch will automatically download the features. The i2022 will then step through each of its programming choices and give you the opportunity to make a selection. After you have made the selection press the “MORE” key to continue.

13

Image 15

Contents I2022 Series Isdn Teleset User’s Guide Mandatory Customer Information Federal Communications Commission FCC Requirements, PartTrademark Acknowledgment Introduction Introduction About this ManualI2022 Teleset Voice Operation Features FeaturesInstallation AccessoriesParts List I2022 Equipped with an S Interface Module Switch Settings Power SwitchTR Switch Isdn InterfacesPowering the i2022 Locally PS1/PS2 Switch SettingsUsing Lucent 1215B Power Supply Terminating Resistors POINT-TO-POINT CircuitsPASSIVE-BUS or Multipoint I2022 Equipped with a U Interface Module Line Configuration Inserting and removing the modules Installing the Logo PlateSoftkeys Example AUTO-InstallAuto-SPID Procedures AUTO-SwitchAuto-Download Next Prev Select PromptSpid Manually Choose the Switch Type Manually Entering the SpidPress MENU, MORE, MORE, Config, MORE, MORE, Spid ApplicationPots P+D Data Manual Switch DownloadingManually Programming Call Appearances Page Manually Programming Feature Keys Setting UP the Teleset Adjusting the Display Viewing AngleSetting the Contrast Setting the Backlighting Options Setting the Date and Time Clock Ringing Patterns Enter CA Key or Number Pressed Key Common2nd Ring Confca Conference Call Appearance PrimCA Primary Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Press MENU, Alarm Setting the Alarm TimePassword Selection There are four levels of password protectionSetting Protection Levels Terms and Nomenclature OperationsLanguage Options Voice OperationDisplay Window and Menus NON-PROGRAMMABLE Hardkeys and IndicatorsDialing On-Hook Placing CallsAnswering Incoming Calls Dialing Off-HookHold KEY TRANSFER, Conference and DropTransferring Incoming Calls Conferencing an Incoming Call to an Outgoing Call Way Conferencing Conferencing Two Outgoing CallsTeleset Features RedialDirectory Directory Changes SetupDirectory Searches Dialing Options Setting the Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Dialing from the Call Log Call RecordsSaving a CalLog Entry to the Directory Dial Prev Edit Clear PartyAnalog Port Advanced FeaturesAnalog Port Sharing the Teleset’s Spid Operation Analog Port on a Separate Spid ConfiguringAnalog Port on a Separate Spid Operation Icons Call Blocking ToneDSS/BLF Direct Station SELECT, Busy Lamp Field Disabling Softkeys To program a DSS/BLFDSS/BLF Operation KEY Mapping View Protecting Keys from Being Overwritten Disabling the Automatic DownloadProtecting specific keys from an Automatic Download Disable Logging TestingKEY Clicks Loading FW Troubleshooting ProblemsMaintaining the Teleset Checking the FW VersionCalls Blocked GlossaryPage Liquid Crystal Display LCD IndexSpeaker