Nortel Networks i2022 Series manual Placing Calls, Answering Incoming Calls, Dialing Off-Hook

Page 36

i2022 ISDN Teleset

PLACING CALLS

The two methods of placing calls are On-Hook and Off-Hook dialing.

Dialing Off-Hook

1.Lift the handset (go Off-Hook), listen for dial tone and note the steady, green Call Appearance key.

2.Using the touchtone keypad, dial the number and observe the call timing feature. When the called party answers the call timer begins operation.

3.Return the handset to the switch hook cradle (go On-Hook) to disconnect.

Dialing On-Hook

1.The handset remains On-Hook while you dial the number. Note that the dialed digits appear on the screen as they are dialed.

2.Press Cancel to abort the dialing process, or use Bkspc to correct the dialed number – one digit at a time.

3.When you are sure that your dialed number is correct, go Off-Hook. The number is dialed and the call timer begins as the call is answered.

4.When the call is over, go On-Hook.

ANSWERING INCOMING CALLS

Line Preference

There are four options for answering incoming calls: Ringing Line Preference, Idle Line Preference, Key 1 Preference, and No Preference (see Advanced Features). In all cases, the Call Appearance hardkey flashes (red) and the Caller ID data, if sent by the switch, is displayed on the screen.

1.Idle Line Preference, the user goes Off Hook and presses the ringing Call Appearance key to answer the call. Idle Line Preference seeks the first available idle line and returns dial tone.

2.Ringing Line Preference, the user goes Off-Hook to answer the call. Pressing the ringing key is not required. In the case of multiple ringing calls the oldest ringing Prime Call Appearance is answered (See PrimCA Primary Call Appearance). This is the most common operation.

3.Key 1 Preference, the Teleset will always go off hook on Key 1 regardless if the Call Appearance is ringing or idle.

4.No Preference, the user must select a Call Appearance key every time it is ringing or dial tone is requested. The

phone will not automatically select a Call Appearance.

To set the Line Preference press MENU, MORE, MORE, LnPrf.

Display Information

Incoming calls will display Calling Line ID as a Calling Party Number or a Calling Party Name and Number, depending on the configuration of the serving telephone company switch. Figure 11 is an answered, incoming call with Calling Party Number only.

Figure 11: Active Call Number Only

34

Image 36
Contents I2022 Series Isdn Teleset User’s Guide Mandatory Customer Information Federal Communications Commission FCC Requirements, PartTrademark Acknowledgment Introduction Introduction About this ManualI2022 Teleset Features Voice Operation FeaturesInstallation AccessoriesParts List Switch Settings Power Switch TR SwitchIsdn Interfaces I2022 Equipped with an S Interface ModulePS1/PS2 Switch Settings Powering the i2022 LocallyUsing Lucent 1215B Power Supply Terminating Resistors POINT-TO-POINT CircuitsPASSIVE-BUS or Multipoint I2022 Equipped with a U Interface Module Line Configuration Installing the Logo Plate Inserting and removing the modulesSoftkeys AUTO-Install ExampleAUTO-Switch Auto-SPID ProceduresNext Prev Select Prompt Auto-DownloadManually Choose the Switch Type Manually Entering the Spid Press MENU, MORE, MORE, Config, MORE, MORE, SpidApplication SpidManual Switch Downloading Pots P+D DataManually Programming Call Appearances Page Manually Programming Feature Keys Setting UP the Teleset Adjusting the Display Viewing AngleSetting the Contrast Setting the Backlighting Options Setting the Date and Time Clock Enter CA Key or Number Pressed Key Common Ringing Patterns2nd Ring PrimCA Primary Call Appearance Confca Conference Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Setting the Alarm Time Press MENU, AlarmPassword Selection There are four levels of password protectionSetting Protection Levels Operations Language OptionsVoice Operation Terms and NomenclatureNON-PROGRAMMABLE Hardkeys and Indicators Display Window and MenusPlacing Calls Answering Incoming CallsDialing Off-Hook Dialing On-HookHold KEY TRANSFER, Conference and DropTransferring Incoming Calls Way Conferencing Conferencing Two Outgoing Calls Conferencing an Incoming Call to an Outgoing CallTeleset Features RedialDirectory Setup Directory ChangesDirectory Searches Setting the Dialing Options Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Call Records Dialing from the Call LogDial Prev Edit Clear Party Saving a CalLog Entry to the DirectoryAdvanced Features Analog PortAnalog Port on a Separate Spid Configuring Analog Port Sharing the Teleset’s Spid OperationAnalog Port on a Separate Spid Operation Call Blocking Tone IconsDSS/BLF Direct Station SELECT, Busy Lamp Field Disabling Softkeys To program a DSS/BLFDSS/BLF Operation KEY Mapping View Protecting Keys from Being Overwritten Disabling the Automatic DownloadProtecting specific keys from an Automatic Download Disable Logging TestingKEY Clicks Troubleshooting Problems Maintaining the TelesetChecking the FW Version Loading FWGlossary Calls BlockedPage Index Liquid Crystal Display LCDSpeaker