Nortel Networks i2022 Series manual Pots P+D Data, Manual Switch Downloading

Page 19

i2022 ISDN Teleset

4.Up to twenty digits can be entered as the SPID. After entering the digits, press Save to enter into non-volatile memory. If an error is made use the Bkspc (backspace) key to edit. Enter the corrected digits and press Save.

5. Choose the Service you require. (Voice is the default) See Table 4.

Serviced as Voice SPID1 = 84755547360101 [(P+D)=POTS+Data]

POTS (P+D) Data

MORE is flashing

Press MENU to exit.

When the SPID entry is complete, the Teleset must be programmed.

The i2022Teleset can download the switch parameters, and/or can be manually programmed.

Manual Switch Downloading

Switch parameters may be downloaded from the switch to the Teleset over the ISDN line. A download can be requested up to three times in a five-minute period. To download proceed as follows:

1.Press MENU, MORE, MORE, Config, MORE, MORE, and ReqParam/RunSPM (depending on the switch) in order. A message indicates a successful or failed download. If the switch is in the Auto-SPID/Auto-Switch mode, the download is automatic upon initialization. If successful, the remainder of the setup parameters need not be entered. These setup characteristics include conference, drop, transfer and Call Appearances. You must enter these parameters manually if the download fails. Press MENU to return to the idle (power-up) screen.

NOTE: If the Teleset detects a DMS-100®or the switch is programmed as a DMS-100®, the ReqParam softkey will be displayed as RunSPM.

NOTE: If the Teleset has not linked with the switch, the display will show “Layer 3 Not Initialized”, “Data Link Down” or “Line Not Ready”.

NOTE: Parameter Downloading applies to SPID 1 only.

17

Image 19

Contents I2022 Series Isdn Teleset User’s Guide Federal Communications Commission FCC Requirements, Part Mandatory Customer InformationTrademark Acknowledgment Introduction About this Manual IntroductionI2022 Teleset Voice Operation Features FeaturesAccessories InstallationParts List I2022 Equipped with an S Interface Module Switch Settings Power SwitchTR Switch Isdn InterfacesPowering the i2022 Locally PS1/PS2 Switch SettingsUsing Lucent 1215B Power Supply POINT-TO-POINT Circuits Terminating ResistorsPASSIVE-BUS or Multipoint I2022 Equipped with a U Interface Module Line Configuration Inserting and removing the modules Installing the Logo PlateSoftkeys Example AUTO-InstallAuto-SPID Procedures AUTO-SwitchAuto-Download Next Prev Select PromptSpid Manually Choose the Switch Type Manually Entering the SpidPress MENU, MORE, MORE, Config, MORE, MORE, Spid ApplicationPots P+D Data Manual Switch DownloadingManually Programming Call Appearances Page Manually Programming Feature Keys Adjusting the Display Viewing Angle Setting UP the TelesetSetting the Contrast Setting the Backlighting Options Setting the Date and Time Clock Ringing Patterns Enter CA Key or Number Pressed Key Common2nd Ring Confca Conference Call Appearance PrimCA Primary Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Press MENU, Alarm Setting the Alarm TimeThere are four levels of password protection Password SelectionSetting Protection Levels Terms and Nomenclature OperationsLanguage Options Voice OperationDisplay Window and Menus NON-PROGRAMMABLE Hardkeys and IndicatorsDialing On-Hook Placing CallsAnswering Incoming Calls Dialing Off-HookTRANSFER, Conference and Drop Hold KEYTransferring Incoming Calls Conferencing an Incoming Call to an Outgoing Call Way Conferencing Conferencing Two Outgoing CallsRedial Teleset FeaturesDirectory Directory Changes SetupDirectory Searches Dialing Options Setting the Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Dialing from the Call Log Call RecordsSaving a CalLog Entry to the Directory Dial Prev Edit Clear PartyAnalog Port Advanced FeaturesAnalog Port Sharing the Teleset’s Spid Operation Analog Port on a Separate Spid ConfiguringAnalog Port on a Separate Spid Operation Icons Call Blocking ToneDSS/BLF Direct Station SELECT, Busy Lamp Field To program a DSS/BLF Disabling SoftkeysDSS/BLF Operation KEY Mapping View Disabling the Automatic Download Protecting Keys from Being OverwrittenProtecting specific keys from an Automatic Download Testing Disable LoggingKEY Clicks Loading FW Troubleshooting ProblemsMaintaining the Teleset Checking the FW VersionCalls Blocked GlossaryPage Liquid Crystal Display LCD IndexSpeaker