Nortel Networks i2022 Series Application, Press MENU, MORE, MORE, Config, MORE, MORE, Spid

Page 18

i2022 ISDN Teleset

Connecting the I2022- Manual-install

1. Assemble the i2022

NOTE: Make sure the logo plate is installed

2.Verify the PS1/PS2 switch located on the Interface Module is in the PS2 position. See page 6 for further information on setting the PS1/PS2 switch.

3.Verify the Terminating Resistor (TR) switch is set correctly. See page 8 for further information on setting the TR switch.

4.Connect one end of the eight-pin mounting cord to the ISDN Line-In jack on the bottom of the Teleset. Connect the other end of the cord to the S/T jack on your NT1 or ISDN telephone wall jack.

5.Remove the protective film on the display.

6.Label and install the designation card

Manually Choose the Switch Type

NOTE: Your Teleset has a factory default setting of “AUTO” which adjusts to the switch type. An incorrect switch type results in a warning message from the Teleset. The correct switch type, as detected by the Teleset, is displayed as a prompt to change your switch selection.

Manually Entering the SPID

The i2022 supports up to two SPIDs. The two SPIDs are designated

SPID 1 and SPID 2. Both SPIDs can be configured to meet a variety of applications. See Table 4.

APPLICATION

Voice Only

Voice with alternate Analog Port on Call Appearance 1

Voice with alternate Data on Call Appearance 1

Voice with alternate Analog Port and Data on Call Appearance 1

Voice with simultaneous Data

Voice with simultaneous Analog Port

Voice with simultaneous, alternate Data and Analog Port

Voice with alternate analog port and simultaneous Data

Voice with alternate Data and simultaneous analog port

NOTE: POTS is the Analog Port.

Table 4

To change either or both SPIDS:

SPID 1

Voice & <option> Voice & POTS Voice & Data Voice & (P+D) Voice & <option> Voice & <option> Voice & <option> Voice & POTS Voice & Data

SPID 2

NULL

NULL

NULL

NULL

Data

POTS

Data & POTS

Data

POTS

1.Press MENU, MORE, MORE, Config, MORE, MORE, SPID.

2.Select the SPID you wish to change.

3.Press Change if you want to edit the SPID. Pressing Change will not erase the displayed SPID until the new SPID is entered from the keypad. Press Clear if you want to erase the existing SPID.

[Enter the Phone SPID] SPID1 = 84755547360101

Auto Bkspc Save

MORE is flashing

16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents I2022 Series Isdn Teleset User’s Guide Mandatory Customer Information Federal Communications Commission FCC Requirements, PartTrademark Acknowledgment Introduction Introduction About this ManualI2022 Teleset Features Voice Operation FeaturesInstallation AccessoriesParts List Isdn Interfaces Switch Settings Power SwitchTR Switch I2022 Equipped with an S Interface ModulePS1/PS2 Switch Settings Powering the i2022 LocallyUsing Lucent 1215B Power Supply Terminating Resistors POINT-TO-POINT CircuitsPASSIVE-BUS or Multipoint I2022 Equipped with a U Interface Module Line Configuration Installing the Logo Plate Inserting and removing the modulesSoftkeys AUTO-Install ExampleAUTO-Switch Auto-SPID ProceduresNext Prev Select Prompt Auto-DownloadApplication Manually Choose the Switch Type Manually Entering the SpidPress MENU, MORE, MORE, Config, MORE, MORE, Spid SpidManual Switch Downloading Pots P+D DataManually Programming Call Appearances Page Manually Programming Feature Keys Setting UP the Teleset Adjusting the Display Viewing AngleSetting the Contrast Setting the Backlighting Options Setting the Date and Time Clock Enter CA Key or Number Pressed Key Common Ringing Patterns2nd Ring PrimCA Primary Call Appearance Confca Conference Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Setting the Alarm Time Press MENU, AlarmPassword Selection There are four levels of password protectionSetting Protection Levels Voice Operation OperationsLanguage Options Terms and NomenclatureNON-PROGRAMMABLE Hardkeys and Indicators Display Window and MenusDialing Off-Hook Placing CallsAnswering Incoming Calls Dialing On-HookHold KEY TRANSFER, Conference and DropTransferring Incoming Calls Way Conferencing Conferencing Two Outgoing Calls Conferencing an Incoming Call to an Outgoing CallTeleset Features RedialDirectory Setup Directory ChangesDirectory Searches Setting the Dialing Options Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Call Records Dialing from the Call LogDial Prev Edit Clear Party Saving a CalLog Entry to the DirectoryAdvanced Features Analog PortAnalog Port on a Separate Spid Configuring Analog Port Sharing the Teleset’s Spid OperationAnalog Port on a Separate Spid Operation Call Blocking Tone IconsDSS/BLF Direct Station SELECT, Busy Lamp Field Disabling Softkeys To program a DSS/BLFDSS/BLF Operation KEY Mapping View Protecting Keys from Being Overwritten Disabling the Automatic DownloadProtecting specific keys from an Automatic Download Disable Logging TestingKEY Clicks Checking the FW Version Troubleshooting ProblemsMaintaining the Teleset Loading FWGlossary Calls BlockedPage Index Liquid Crystal Display LCDSpeaker
Top Page Image Contents