Nortel Networks i2022 Series manual Teleset Features, Redial, Directory

Page 39

i2022 ISDN Teleset

Conferencing an Outgoing Call to an Incoming Call

1.Place the outgoing call on Hold by using the Hold key.

2.The outgoing Call Appearance will flash red.

3.Answer the incoming call.

4.Press the Conf (conference) softkey and the phone adds dial tone from another Call Appearance. Ignore the dial tone!

5.Press the first (outgoing) Call Appearance and the dial tone stops.

6.Press the Join key and the conference is completed.

Conferencing Two Incoming Calls

1.Place the first incoming call on Hold – the first Call Appearance flashes red.

2.Answer the second incoming call.

3.Press the Conf softkey. As above, ignore the dial tone you hear from another Call Appearance.

4.Press the first Call Appearance, then press Join - the conference is completed.

The Drop Feature

The Drop softkey will be available whenever the Teleset is off hook. The function of the Drop feature varies depending on the call state.

When off hook to dial tone or a partially dialed number, or a ringing number, pressing the Drop key will disconnect the current call and cause the i2022 to revert back to dial tone

When on an active single party (non-conferenced) call, pressing the Drop key will disconnect the current call and cause the i2022 to revert back to dial tone

When on an active conference call and the controller of the conference, pressing the Drop key will disconnect the last party added to the conference call. Subsequent pressings of the Drop key will disconnect the call and the i2022 will revert back to dial tone.

When on an active conference call and NOT the controller of the conference, pressing the Drop key will disconnect the current call and cause the i2022 to revert back to dial tone

NOTE: Some switches may have multiple drop keys. These drop keys, if available, will be found as one or more of the Programmable Hardkeys.

TELESET FEATURES

REDIAL

Press this key to automatically dial the last manually dialed, or Speed Dialed number. This is especially handy when trying to connect to a frequently busy number.

1.Go Off-Hook.

2.When dial tone is received, press the REDIAL key. Pressing this key without going Off-Hook enables the speakerphone. The last manually dialed number is dialed for you.

3.Go On-Hook when the call is completed.

DIRECTORY

The following characteristics apply to entries placed in the Directory:

A name may be up to 20 characters in length. A Directory Number (DN) can be 32 digits long.

The directory capacity is 100 entries - stored in alphabetical order.

Search hint: If you forget the name you are looking for, press “Find/Next” and you can scroll through the entries.

37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents I2022 Series Isdn Teleset User’s Guide Mandatory Customer Information Federal Communications Commission FCC Requirements, PartTrademark Acknowledgment Introduction Introduction About this ManualI2022 Teleset Voice Operation Features FeaturesInstallation AccessoriesParts List I2022 Equipped with an S Interface Module Switch Settings Power SwitchTR Switch Isdn InterfacesPowering the i2022 Locally PS1/PS2 Switch SettingsUsing Lucent 1215B Power Supply Terminating Resistors POINT-TO-POINT CircuitsPASSIVE-BUS or Multipoint I2022 Equipped with a U Interface Module Line Configuration Inserting and removing the modules Installing the Logo PlateSoftkeys Example AUTO-InstallAuto-SPID Procedures AUTO-SwitchAuto-Download Next Prev Select PromptSpid Manually Choose the Switch Type Manually Entering the SpidPress MENU, MORE, MORE, Config, MORE, MORE, Spid ApplicationPots P+D Data Manual Switch DownloadingManually Programming Call Appearances Page Manually Programming Feature Keys Setting UP the Teleset Adjusting the Display Viewing AngleSetting the Contrast Setting the Backlighting Options Setting the Date and Time Clock Ringing Patterns Enter CA Key or Number Pressed Key Common2nd Ring Confca Conference Call Appearance PrimCA Primary Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Press MENU, Alarm Setting the Alarm TimePassword Selection There are four levels of password protectionSetting Protection Levels Terms and Nomenclature OperationsLanguage Options Voice OperationDisplay Window and Menus NON-PROGRAMMABLE Hardkeys and IndicatorsDialing On-Hook Placing CallsAnswering Incoming Calls Dialing Off-HookHold KEY TRANSFER, Conference and DropTransferring Incoming Calls Conferencing an Incoming Call to an Outgoing Call Way Conferencing Conferencing Two Outgoing CallsTeleset Features RedialDirectory Directory Changes SetupDirectory Searches Dialing Options Setting the Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Dialing from the Call Log Call RecordsSaving a CalLog Entry to the Directory Dial Prev Edit Clear PartyAnalog Port Advanced FeaturesAnalog Port Sharing the Teleset’s Spid Operation Analog Port on a Separate Spid ConfiguringAnalog Port on a Separate Spid Operation Icons Call Blocking ToneDSS/BLF Direct Station SELECT, Busy Lamp Field Disabling Softkeys To program a DSS/BLFDSS/BLF Operation KEY Mapping View Protecting Keys from Being Overwritten Disabling the Automatic DownloadProtecting specific keys from an Automatic Download Disable Logging TestingKEY Clicks Loading FW Troubleshooting ProblemsMaintaining the Teleset Checking the FW VersionCalls Blocked GlossaryPage Liquid Crystal Display LCD IndexSpeaker
Top Page Image Contents