Nortel Networks i2022 Series manual KEY Clicks, Disable Logging, Testing

Page 56

i2022 ISDN Teleset

To unprotect the keys, press them again and the key will go dark.

NOTE: Protecting the keys does not prevent Speed dial keys from being changed locally using Menu, SpDial.

KEY CLICKS

Key clicks can be enabled or disabled by pressing MENU, and dialing 96 on the touchtone keypad.

DISABLE LOGGING

Call logs can be disabled completely so that no calls will log, or, they can be disabled so “shared” Call Appearances will not log.

Disabling Call Logs Completely

To disable Call Logging so NO calls will log, press MENU and dial 97 on the touchtone keypad. Press Yes to disable call logging. Press No to enable call logging.

Disable Call Logs On Shared Call Appearance

Call Logs can be disabled on Shared Call Appearances by changing the Shared Call Appearances from Prime Call Appearances to General Call Appearances.

To change Prime Call Appearances to General Call Appearances, press MENU, MORE, MORE, Config, MORE, PrimCA. For further information, see “PrimCA (Primary Call Appearance)”.

NOTE: Remember, changing a Prime CA to a General CA, removes it from the Call Appearances that will be answered by Ringing Line Preference.

TESTING

You can test the operation of your Teleset by using a simple, built-in diagnostic procedure. To begin, follow these steps.

1.Press MENU, MORE, Test

2.Select the test you wish to run.

3.Press the MENU key to exit.

CODE

ERROR TYPE

MEANING

01

RAM Error

Failure in RAM or associated circuits

04

RTC Error

Failure in the clock or associated circuits

08

FLASH Error

Failure in memory or associated circuits

10

S Error

Failure detected on the S Interface

20

E Error

Failure detected on the U Interface

40

F Error

Failure detected in FW Download

“RTC” and an “S Interface” error has occurred in self-test.

54

Error Types have “or bit relation”. This means the code being displayed may be a combination of more than one error code. For example, if the error code displayed is “10”, it would mean an “S-Interface” has error has

occurred in self-test. If the error code displayed is “1C”, it would mean a “Flash”,

Image 56
Contents I2022 Series Isdn Teleset User’s Guide Trademark Acknowledgment Mandatory Customer InformationFederal Communications Commission FCC Requirements, Part Introduction I2022 Teleset IntroductionAbout this Manual Features Voice Operation FeaturesParts List InstallationAccessories Switch Settings Power Switch TR SwitchIsdn Interfaces I2022 Equipped with an S Interface ModulePS1/PS2 Switch Settings Powering the i2022 LocallyUsing Lucent 1215B Power Supply PASSIVE-BUS or Multipoint Terminating ResistorsPOINT-TO-POINT Circuits I2022 Equipped with a U Interface Module Line Configuration Installing the Logo Plate Inserting and removing the modulesSoftkeys AUTO-Install ExampleAUTO-Switch Auto-SPID ProceduresNext Prev Select Prompt Auto-DownloadManually Choose the Switch Type Manually Entering the Spid Press MENU, MORE, MORE, Config, MORE, MORE, SpidApplication SpidManual Switch Downloading Pots P+D DataManually Programming Call Appearances Page Manually Programming Feature Keys Setting the Contrast Setting UP the TelesetAdjusting the Display Viewing Angle Setting the Backlighting Options Setting the Date and Time Clock Enter CA Key or Number Pressed Key Common Ringing Patterns2nd Ring PrimCA Primary Call Appearance Confca Conference Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Setting the Alarm Time Press MENU, AlarmSetting Protection Levels Password SelectionThere are four levels of password protection Operations Language OptionsVoice Operation Terms and NomenclatureNON-PROGRAMMABLE Hardkeys and Indicators Display Window and MenusPlacing Calls Answering Incoming CallsDialing Off-Hook Dialing On-HookTransferring Incoming Calls Hold KEYTRANSFER, Conference and Drop Way Conferencing Conferencing Two Outgoing Calls Conferencing an Incoming Call to an Outgoing CallDirectory Teleset FeaturesRedial Setup Directory ChangesDirectory Searches Setting the Dialing Options Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Call Records Dialing from the Call LogDial Prev Edit Clear Party Saving a CalLog Entry to the DirectoryAdvanced Features Analog PortAnalog Port on a Separate Spid Configuring Analog Port Sharing the Teleset’s Spid OperationAnalog Port on a Separate Spid Operation Call Blocking Tone IconsDSS/BLF Direct Station SELECT, Busy Lamp Field DSS/BLF Operation Disabling SoftkeysTo program a DSS/BLF KEY Mapping View Protecting specific keys from an Automatic Download Protecting Keys from Being OverwrittenDisabling the Automatic Download KEY Clicks Disable LoggingTesting Troubleshooting Problems Maintaining the TelesetChecking the FW Version Loading FWGlossary Calls BlockedPage Index Liquid Crystal Display LCDSpeaker