Nortel Networks i2022 Series Operations, Language Options, Voice Operation, Call Appearance LED’S

Page 34

i2022 ISDN Teleset

5.This number is your password. Write it down. You are prompted to confirm the password.

6.To begin Level 2 protection, press the lit MENU hardkey now. Do not press the Menus softkey. Level 2 protection is now set.

7.To begin Level 3 protection, enter your password and press the Menus softkey. Level 3 protects the Teleset’s entire menu system.

8.To begin Level 4 protection, enter your password and press the Total softkey. Level 4 protection does not begin until 10 seconds after choosing this option or 10 seconds after the phone is used.

9.Press MENU to exit.

LANGUAGE OPTIONS

Certain keycaps are available in three languages. These user changeable keycaps are shown below. The Teleset will also allow the user to choose a display language.

English

French

MENU

MENU

MUTE

SOUR

HOLD

ATTENT

REDIAL

RECOMP

Table 1

Changing the Keycaps

Spanish

MENU

MUTE

ESPERA

VOL.LL

Using a small screwdriver or similar flat blade (unsharpened), carefully pry-up the existing keycap by the indentation on the side. Remove the keycap and gently press the new cap down until it locks in place. You may now change the language displayed.

Changing the Display Language

Press the following keys in order: MENU, MORE, MORE, Config, LANG. The Teleset will then prompt you to choose the desired language.

OPERATIONS

VOICE OPERATION

Most of the operations described to this point are switch related or controlled. Voice Operation consists of features/options controlled by the Teleset.

TERMS AND NOMENCLATURE

Of all the terms used in basic telephony, none is more widely used than “On-Hook and Off-Hook.” They refer to placing or removing the handset, or receiver, in the cradle (usually on the top or in the front) of the instrument. The button protruding up from the cradle is the “On and Off” switch, or switch hook, of the phone. Pressing the Speaker key and requesting dial tone is also considered going “Off-Hook”. This background is helpful in understanding the instructions that follow.

CALL APPEARANCE LED’S

The various states of the Call Appearance indicators (hardkeys) are described in the following table.

LED State

Meaning

Off

Idle State

Red – Flashing Slow

Incoming Call

Red – Flashing Fast

Call on Hold (Local)

Green – Flashing Fast

Call on Hold (Shared)

Green - Steady

Call in Progress

Table 5

32

Page 33 Page 35
Image 34
Page 33 Page 35
Contents I2022 Series Isdn Teleset User’s Guide Federal Communications Commission FCC Requirements, Part Mandatory Customer InformationTrademark Acknowledgment Introduction About this Manual IntroductionI2022 Teleset Features Voice Operation FeaturesAccessories InstallationParts List Isdn Interfaces Switch Settings Power SwitchTR Switch I2022 Equipped with an S Interface ModulePS1/PS2 Switch Settings Powering the i2022 LocallyUsing Lucent 1215B Power Supply POINT-TO-POINT Circuits Terminating ResistorsPASSIVE-BUS or Multipoint I2022 Equipped with a U Interface Module Line Configuration Installing the Logo Plate Inserting and removing the modulesSoftkeys AUTO-Install ExampleAUTO-Switch Auto-SPID ProceduresNext Prev Select Prompt Auto-DownloadApplication Manually Choose the Switch Type Manually Entering the SpidPress MENU, MORE, MORE, Config, MORE, MORE, Spid SpidManual Switch Downloading Pots P+D DataManually Programming Call Appearances Page Manually Programming Feature Keys Adjusting the Display Viewing Angle Setting UP the TelesetSetting the Contrast Setting the Backlighting Options Setting the Date and Time Clock Enter CA Key or Number Pressed Key Common Ringing Patterns2nd Ring PrimCA Primary Call Appearance Confca Conference Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Setting the Alarm Time Press MENU, AlarmThere are four levels of password protection Password SelectionSetting Protection Levels Voice Operation OperationsLanguage Options Terms and NomenclatureNON-PROGRAMMABLE Hardkeys and Indicators Display Window and MenusDialing Off-Hook Placing CallsAnswering Incoming Calls Dialing On-HookTRANSFER, Conference and Drop Hold KEYTransferring Incoming Calls Way Conferencing Conferencing Two Outgoing Calls Conferencing an Incoming Call to an Outgoing CallRedial Teleset FeaturesDirectory Setup Directory ChangesDirectory Searches Setting the Dialing Options Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Call Records Dialing from the Call LogDial Prev Edit Clear Party Saving a CalLog Entry to the DirectoryAdvanced Features Analog PortAnalog Port on a Separate Spid Configuring Analog Port Sharing the Teleset’s Spid OperationAnalog Port on a Separate Spid Operation Call Blocking Tone IconsDSS/BLF Direct Station SELECT, Busy Lamp Field To program a DSS/BLF Disabling SoftkeysDSS/BLF Operation KEY Mapping View Disabling the Automatic Download Protecting Keys from Being OverwrittenProtecting specific keys from an Automatic Download Testing Disable LoggingKEY Clicks Checking the FW Version Troubleshooting ProblemsMaintaining the Teleset Loading FWGlossary Calls BlockedPage Index Liquid Crystal Display LCDSpeaker
Top Page Image Contents