Nortel Networks i2022 Series manual AUTO-Switch, Auto-SPID Procedures

Page 16

i2022 ISDN Teleset

NOTE: You may abort the Auto-Installby pressing the Menu key at any time

The Auto-Installprogramming choices are:

Adjust Contrast – Select Yes or No. The i2022 may display a wait message and start a countdown. This is the T- Wait timer.

NOTE You can abort the T-Wait countdown timer at any time by pressing the Speaker key or any touchtone keypad digit.

SPID – If the switch supports Auto-SPID you will be prompted to choose a SPID. If your switch does not support Auto-SPID, press the “Change” softkey and enter the SPID. After entering the SPID press “Save”.

The Teleset will attempt to initialize. If there is a problem the Teleset will prompt you to correct the SPID and/or switch type.

The Teleset will download its configuration from the switch. If Parameter Downloading is not available, you will be prompted to program the Teleset manually.

Backlight – Select On, Off, or Dynamic. Enter the Date and Time.

Adjust the Ring Pattern – Select Yes or No.

Set the 2nd ring Option – Select Continuous, Partial, or No Ring. Set the Analog Call Appearance.

Set Primary Call Appearances. Set an Intercom Key.

Set Speed Dial Keys.

Set the Alarm Clock. Set a Password. Set Line Preference.

NOTE: Auto-Install will only run when the i2022 is in the default mode.

NOTE: To default the i2022 press MENU and enter 91 from the dial keypad. Press the “YES” softkey to complete the default.

WARNING: DEFAULTING THE i2022 WILL ERASE ALL OF THE MEMORY.

AUTO-Switch

With Auto-Switch detection, the i2022 determines the type of switch to which you are connected. Should you decide to manually program the switch type, Auto-Switch detect will tell you if a different type of switch is found. You will then be given the opportunity to correct the switch type.

AUTO-SPID

Auto-SPID is a National 2 and National 3 ISDN feature. Not all switch types and not all service providers support the Auto- SPID feature. If Auto-SPID is supported, follow the procedure shown below.

Auto-SPID Procedures

When the countdown timer stops, or is aborted, the Teleset automatically sends the Auto-SPID code to the switch. Upon receipt of the Auto-SPID code, the switch will download all of the SPID’s that are supported on that line.

NOTE: If the SPID is not accepted for any reason - including the SPID being used at another location - the phone displays: “Invalid SPID,” and allows correction of the SPID.

14

Page 15 Page 17
Image 16
Page 15 Page 17
Contents I2022 Series Isdn Teleset User’s Guide Federal Communications Commission FCC Requirements, Part Mandatory Customer InformationTrademark Acknowledgment Introduction About this Manual IntroductionI2022 Teleset Features Voice Operation FeaturesAccessories InstallationParts List Switch Settings Power Switch TR SwitchIsdn Interfaces I2022 Equipped with an S Interface ModulePS1/PS2 Switch Settings Powering the i2022 LocallyUsing Lucent 1215B Power Supply POINT-TO-POINT Circuits Terminating ResistorsPASSIVE-BUS or Multipoint I2022 Equipped with a U Interface Module Line Configuration Installing the Logo Plate Inserting and removing the modulesSoftkeys AUTO-Install ExampleAUTO-Switch Auto-SPID ProceduresNext Prev Select Prompt Auto-DownloadManually Choose the Switch Type Manually Entering the Spid Press MENU, MORE, MORE, Config, MORE, MORE, SpidApplication SpidManual Switch Downloading Pots P+D DataManually Programming Call Appearances Page Manually Programming Feature Keys Adjusting the Display Viewing Angle Setting UP the TelesetSetting the Contrast Setting the Backlighting Options Setting the Date and Time Clock Enter CA Key or Number Pressed Key Common Ringing Patterns2nd Ring PrimCA Primary Call Appearance Confca Conference Call AppearanceIntercom Speed Dial Key Assignment Editing a Speed Dial Number Setting the Alarm Time Press MENU, AlarmThere are four levels of password protection Password SelectionSetting Protection Levels Operations Language OptionsVoice Operation Terms and NomenclatureNON-PROGRAMMABLE Hardkeys and Indicators Display Window and MenusPlacing Calls Answering Incoming CallsDialing Off-Hook Dialing On-HookTRANSFER, Conference and Drop Hold KEYTransferring Incoming Calls Way Conferencing Conferencing Two Outgoing Calls Conferencing an Incoming Call to an Outgoing CallRedial Teleset FeaturesDirectory Setup Directory ChangesDirectory Searches Setting the Dialing Options Dialing OptionsControl Type Semi Auto Phone Number 847 Next Change Use Keypad to Enter 1 Nxx Clear Save Call Records Dialing from the Call LogDial Prev Edit Clear Party Saving a CalLog Entry to the DirectoryAdvanced Features Analog PortAnalog Port on a Separate Spid Configuring Analog Port Sharing the Teleset’s Spid OperationAnalog Port on a Separate Spid Operation Call Blocking Tone IconsDSS/BLF Direct Station SELECT, Busy Lamp Field To program a DSS/BLF Disabling SoftkeysDSS/BLF Operation KEY Mapping View Disabling the Automatic Download Protecting Keys from Being OverwrittenProtecting specific keys from an Automatic Download Testing Disable LoggingKEY Clicks Troubleshooting Problems Maintaining the TelesetChecking the FW Version Loading FWGlossary Calls BlockedPage Index Liquid Crystal Display LCDSpeaker
Top Page Image Contents