AT&T at&t partner plus communications system manual Installing Telephones and Other Equipment

Page 17

Installing Telephones and Other Equipment

CAUTION: PARTNER phones must be connected with a 2-pair telephone wire. Other equipment must be connected with a 1-pair mounting cord (AT&T D2R mounting cords recommended).

DESK MOUNTING A PARTNER PHONE

Plug one end of the handset cord into the jack on the handset. Plug the other end of the cord into the small jack on the left side of the base.

Plug one end of the telephone mounting cord into the big jack on the base of the phone. Push the cord in place along the channel on the base of the telephone.

If you want to raise the angle of the phone, install the telephone stand. To attach the stand to the base of the phone, gently place the phone upside down with the low end of the phone to your right. Insert the tab on the narrow end of the stand into the right slot on the base of the phone. Then insert the other tab into the left slot, pushing the stand down and slightly inward until the tab locks into place.

Plug the other end of the mounting cord into the modular wall jack.

Test the intercom. Lift the handset, then press an [Intercom] button. You should hear an intercom dial tone. If not see chapter 8, in the System Manager’s Guide (“Phone Has Lights but No Dial Tone”).

Figure 2-2 Desk Mounting a PARTNER Telephone

Test the outside line connection. I-M the handset and press an outside line button. You should hear an outside dial tone. If not, see chapter 8, in the System Manager’s Guide (“Phone Has Lights but No Dial Tone").

Slide theQuick Reference card under the telephone. Label the button sheet and insert as follows:

1Remove the clear plastic cover from the phone--gently press down on the center tab, then lift.

2Place a button label sheet on the phone so the holes on the sheet fit over the buttons.

3Replace the plastic cover.

TEST PROCEDURE FOR PARTNER PHONES

To test the power and lights on a PARTNER phone:

1Press and hold [#] button for 5 seconds.

2Before releasing the [#] button, lift the handset. All lights should light, the ringer should sound, and on the PARTNER display phone, a test pattern should appear on the display. If not, call the Helpline at 1 800 628-2888.

3Replace handset. The phone is in normal operating mode.

2-4 Installing the Hardware

Image 17
Contents AT&T Copyright 1990 AT&T All Rights Reserved Issue October Contents Page About This Guide How to Use This GuideProduct Safety Labels Reference Materials How to Comment on This GuideSystem Components Specifications Other Equipment Control UnitPartner TeIephones Example System Setup An Example System SetupSystem Components and Specifications Specifications Grounding to comply with Underwriters Laboratories UL Technical and Environmental SpecificationsInstalling the Hardware General Guidelines Mount the Backplane on a Wall Installing the Control UnitInstalling the Hardware Press and hold # button for 5 seconds Installing Telephones and Other EquipmentWall Mounting a Partner Telephone Replacing a Module Removing a ModuleSystem Programming Alphabetic List of Procedures Programming Overlay Programming MethodsProgramming Extension Programming Overlay General Instructions System Day Programming ProceduresSystem Date Number of Lines System TimeCode #105 Transfer Return Rings PBX Dial-Out CodeCode #106 ConsiderationCode #107 Recall Timer DurationCode #109 Rotary Dialing Time out Outside ConferenceCode #108 Code #201 Dial ModeCode #202 Line TypeCode #203 Hold Disconnect TimeValid Entries 1 = Assigned Line AssignmentCode #301 Valid Entries 1 = Line Use RestrictionCode #302 Valid Entries 1 = English Display LanguageCode #303 Code #304 Automatic PrivacyCode #305 Abbreviated RingingCopy Settings Code #401 Outgoing Call RestrictionsCode #402 Toll Call Prefix System PasswordCode #403 Valid Entries Any 4 digitsCode #404 Disallowed Phone Number ListsPrevents all ca!ls to area code Code #405 Disallowed List AssignmentCode #406 Emergency Phone Number ListCode #408 Allowed Phone Number ListsCode #407 Code #501 Pickup Group ExtensionsCode #502 Calling Group ExtensionsProgramming Notes Night Service ButtonCode #503 Code #504 Night Service GroupCode #601 Fax Machine ExtensionsValid Entries 1 = Active Music On HoldCode #602 Code #603 HotlineCode #604 Doorphone 1 ExtensionDoorphone 2 Extension Code #605 Code #606 Doorphone Alert ExtensionsCode #728 System Reset Programming Saved System Speed Dial NumbersPress Feature 0 0 . The display reads Function Button Display Description and Example Pause EnableRecall StopCentralized Telephone Programming Personal Speed Dial Numbers Overview Buttons and Labeling Sheets for Partner Phones To exit Automatic Line Selection, press the star * twice Automatic Line SelectionValid Entries Immediate ring Line Ringing OptionsPersonal Speed Dial Numbers Auto Dial Numbers Exclusive Hold Feature CodeDo Not Disturb Recall Save Number RedialLast Number Redial Conference Drop Privacy Touch-Tone EnableMessage Light On Message Light Off Pickup Group Call PickupLoudspeaker Paging Calling Group Programming Method a Programming for Operation Behind PBX or CentrexProgramming Method B Dialing Restrictions Summary No Outside Line AccessOutside Dialing Allowed Dial 1 201 Dial 1 800 Dialing Restrictions An ExampleFCC Information Page Index Hotline #603, 3-31programming for, 2-1standard phone used as I i Wires, connecting, 2-2to 2-3Wiring specifications, 1-5,2-1 O g r a m m i n g Quick Reference System Programming Programming Quick Reference Issue 2, October